The results show that using high and low slab reheating temperature technique, the texture component of hot rolled grain oriented silicon steel is significantly different from that of cold rolled one.
采用取向分布函数及取向线分析方法对取向硅钢高温和低温板坯加热工艺的热轧及冷轧钢板织构进行了研究。
In sheet strips production, the requirement of glancing flatness for cold - rolled sheets i. e. automobile body sheet, tinned steel sheet, silicon steel sheet and aluminium sheet is higher.
在板带生产中，对汽车钢板、镀锡钢板、硅钢板以及航空铝板等冷轧薄板的平直度有很高的要求。
The cold - rolled silicon steel can be affected by many factors, which are hard to analyze and control.
对冷轧硅钢产品质量造成影响的因素很多，分析繁杂，控制难度大。
Based on analysis and study, this paper advances Suggestions and solutions to the problem about iron loss increasing of punched cold-rolled non-oriented silicon steel sheet after heat treatment.
针对冷轧无取向硅钢冲片在热处理后铁损值升高的问题进行了分析研究，并提出了解决措施和建议。
The results show that the grain size of cold-rolled non-oriented silicon steel finished product decreases and benefiting texture component increases with increasing slab reheating temperature.
结果表明，随着铸坯加热温度的提高，冷轧无取向硅钢成品晶粒尺寸减少，有利织构组分增加。
The effect of speed ratio on the texture of non-oriented cold rolled low silicon steel sheet was investigated after cross shear rolling at different speed ratios.
选取低硅无取向硅钢常化态板材，分别在不同速比下进行异步轧制，考察了速比对低硅无取向硅钢冷轧织构的影响。
Series Y3 asynchronous motors is a new series of general purpose low voltage three-phase cage motors designed with cold-rolled silicon steel sheet.
Y 3系列异步电动机是采用冷轧硅钢片作为导磁材料而设计的一般用途低压三相笼型异步电动机基本系列。
Building a temperature and stress field foretell model of hot-rolled silicon steel has become an important segment for improving production quality and increase manufacture efficiency.
建立热轧过程的温度场、应力场预报模型已经成为改善产品质量，提高生产效益的重要环节。
Roasting roller is an unavoidable part in the production of hot rolled silicon steel.
烫辊是热轧硅钢片生产不可避免的环节。
The paper introduced the equipment, technology innovation and application situation of the domestic large-scale and high speed continuous annealing line for cold rolled silicon-steel sheet.
介绍了我国设计建设的大型高速冷轧硅钢片连续退火机组工艺及设备装备水平，技术创新及应用情况。
In this paper, the influencing factor of Continuous Annealing on the surface quality of cold rolled silicon steel strip is introduced.
本文介绍了连续脱碳退火机组对冷轧硅钢板带表面质量的影响因素，提出了连续脱碳退火机组提高冷轧板带质量的措施。
The microstructure and mechanical properties of different finishing temperatures for hot rolled low silicon containing phosphorus TRIP steel were investigated using a laboratory hot rolling mill.
通过实验室热轧试验，研究了不同终轧温度下低硅含磷系热轧TRIP钢的组织特征及性能特点。
Its main transformer is made of imported cold rolled silicon steel, So its power loss is little with low no-load current.
该系列点焊机，主变压器均为进口冷轨硅钢片，因此，主变压器功耗小，各型空载电流小。
The main transformer uses imported quality cool - rolled silicon - steel plate cores , less power loss and small idle current.
主变压器采用进口优质冷扎硅钢片铁芯，其功耗少，空载电流小。
It's inevitable for-hot-rolled silicon steel sheets to produce oxidized scale in the process.
热轧硅钢片在生产过程中不可避免地会产生氧化铁皮。
The main transformer USES imported quality cool-rolled silicon-steel plate cores less power loss and small idle current.
主变压器采用进口优质冷扎硅钢片铁芯，其功耗少，空载电流小。
Suitable for punching cold-rolled steel, silicon steel sheet etc.
适用于冷轧钢片、硅钢片等材料的冲压。
The variation of the texture and magnetic properties of non-oriented silicon steel after being cold-rolled and annealed is studied.
对冷轧及退火后无取向硅钢织构及磁性能的变化进行研究。
Currently, the domestic cold-rolled silicon steel supply falls short of demand and a large amount is imported.
目前，国内冷轧取向硅钢供不应求，每年需较大的进口量。
The main transformer USES imported quality cool-rolled silicon-steel plate cores, less power loss and small idle current.
主变压器采用进口优质冷扎硅钢片铁芯，其功耗少，空载电流小。
The main transformer USES imported quality cool-rolled silicon-steel plate cores, less power loss and small idle current.
主变压器采用进口优质冷扎硅钢片铁芯，其功耗少，空载电流小。
应用推荐