Control of the penetration and width of the back side weld was then achieved by controlling the width of an isothermal line near the melting point.
通过控制接近熔点温度的等温线宽度最终实现了对焊缝背面熔宽和熔透的控制。
Push the anchoring side bars against the pinch weld clamp. Hammer the wedges firmly as shown.
将支承侧杆对着焊接压板夹钳推。如图所示的那样用锤子将楔子敲紧。
You should control weld manufacturing process card requirements, or the wrong side GB150 according to above two requirements, you should be able to control in this range.
焊缝应控制你们制造工艺卡的要求，或者按gb150上面的错边两要求，你们应该可以控制在此范围里。
On the basis of calcuiation and experience, through side-bending test, test piece's extensibility is relative small, and its weld surface after processed is unaffected by the piece's surface quality.
根据计算和经验，侧弯伸长率小，且焊缝表面经过加工，不受表面质量影响，所以试验结果更接近实际，更为准确。
At the position of the weld, the inner side of the weld should be stopped.
在定位焊时焊缝内侧应停止充氩维护。
Weld the outer side member with a full butt weld under shielding gas.
用气体保护全对接焊，焊接外侧梁。
No spalled paint exists at the plug weld and for a short distance each side of the plug welds.
在塞焊焊缝处及塞焊周围距离内无细漆碎屑存在。
Single Flange Power Delivery Joint: This product is used to connect Flange on the one side and weld with pipe on the other, modulate the product's length in between.
单法兰传力接头：该产品适用于一边与法兰连接，一边与管道焊接。
Slot welding the 2nd side onto the divisions where there is not enough room for access to weld them on the inside.
槽焊接上的第二方面的分歧那里没有足够的空间进入焊缝他们在里面。
They also serve to stop the back-side of the weld from forming carbide intrusions into the pipes and cones.
他们还有助于阻止后面从形成到管道和视锥细胞碳化物入侵的焊接方面。
Secure the mounts and weld them using a 1 "bead on each side."
安全和焊接他们的坐骑使用1“方珠每个。”
The influence mechanism of the thickness of the nickel coating on the steel side on tension-shear strength of the weld was studied by means of tension-shear tests, SEM and EDS.
借助拉剪试验、SEM和EDS，研究了搭接面低碳钢侧镀镍层厚度对接头拉剪强度的影响机制。
The result shows that laser induced plasma and weld geometry are sensitive to side nozzle height, its inclination angle and side gas flow rate;
结果表明，侧吹喷嘴高度和侧吹流速的变化对光致等离子体行为和焊缝形貌有显著的影响；
The diffusion zone width of main alloying elements increases and hardness of the friction weld zone near TC4 titanium alloy side improves after post-weld heat treatment.
经焊后回火热处理后，主要合金元素沿焊合区的扩散区宽度增大；焊合区钛合金侧硬度值显著提高。
The diffusion zone width of main alloying elements increases and hardness of the friction weld zone near TC4 titanium alloy side improves after post-weld heat treatment.
经焊后回火热处理后，主要合金元素沿焊合区的扩散区宽度增大；焊合区钛合金侧硬度值显著提高。
应用推荐