Multisensory devices have already been developed and tested on reinnervated amputees, relaying sensations of contact, pressure, vibration, shear force and temperature.
多重感受装置已经研制出来并在经过神经移植的截肢患者身上测试，转换接触、压力、震动、剪切力和温度的感觉。
It was found that the amount of the grains broke increased with the shear strain and confining pressure, independent of the initial density of the specimen.
试验表明，颗粒破坏的数量随着剪切变形和侧限压力的增大而增多，与试样的初始密度却无直接关系。
Through solving the blood flow equations for local vessel expansion region, the analytical expressions of blood flow velocity, pressure and wall shear stress were then obtained.
接着，通过求解局部扩张血管段内的血液流动方程，导得血液流速、压力和血管壁切应力的分析表达式。
In the color mapping, localized elevation of blood pressure and shear stress could be observed on each plaque surface.
在彩色地图中，在每个斑块的表面都可观察到血压和切应力的局部升高。
As examples, the critical loads of annular plates under the uniform radial pressure and shear forces are given.
作为算例，给出了环形板在中面均匀径向压力和剪切力作用下的临界载荷。
Percent shear fracture appearance is an important factor to evaluate neutron irradiation embrittlement of nuclear pressure vessel steel.
在核压力容器钢的中子辐照脆化评价中，断口剪切面积百分比是一个重要的参数。
The three dimension flow field in the triple-screw extruder with triangle configuration is the research objects, including velocity field, pressure field and shear rate field etc.
本课题以三角形排列的三螺杆挤出机三维流场为研究目标，研究内容包括速度场、压力场、剪切速率场等。
The deformation and contact frictional force of elastomer pressure shear break are studied in proportion loading .
对比例加载时弹性体压剪裂缝的变形及接触摩擦力问题进行了研究。
Softwares ANSYS and MATLAB were employed to analyze and simulate the velocity, pressure and shear stress distribution in sheet extruder dies based on the three-dimensional FEM.
利用ANSYS和MATLAB软件，对缩放型片材机头中熔体的速度、压力和剪切应力的分布进行三维有限元模拟和分析。
Some behaviors of saturated flyash such as pore water pressure, dynamic strength, and dynamic deformation are studied by the dynamic torsional shear test.
通过动扭剪试验研究饱和粉煤灰的动孔隙水压力特性、动强度特性以及振陷变形特性。
The strength resisting liquefaction increases along with the increase of consolidation pressure, sample density initial shear stress, but the increase of initial shear stress is limited.
抗液化强度随固结压力、试样密度、初始剪应力的增加而增加，但初始剪应力的增加量是有一定限度的。
The results show that proper pressure and interlayer thickness can evidently improve the microstructure and mechanical properties, and the shear strength of joint is increased with the holding time.
结果表明：合适的压力和中间层厚度能有效改善接头的组织和力学性能，接头剪切强度随保温时间延长而提高。
The proposed model takes into account the shear modulus, the damping ratio, pore water pressure and permanent deformations of pavement foundation materials.
该模型可以全面考虑路基材料的剪切模量、阻尼比、孔隙水压力以及永久变形。
The mechanical behavior of steel webs with negative bending was studied with combined stress loads of flexure, axial pressure and shear to prevent local buckling in continuous composite beams.
为避免钢混凝土连续组合梁发生局部失稳，对负弯区钢梁腹板在弯曲应力、轴向压应力和剪应力联合作用下的力学性能进行了研究。
The influence of confining pressure and drainage shear condition and initial relative density for flyash in steady-state deformation characteristic were discussed.
着重研究了周围压力、剪切排水条件、初始相对密实度对粉煤灰稳态变形特性的影响；
Meanwhile, the law of soft clay strength improvement is drawn from different consolidated pressure and different degree of consolidation by many consolidated-quickly shear test.
再通过大量的固结快剪试验，得到软粘土在不同固结压力、不同固结度下的强度变化规律。
The influences of confining pressure, end constraint, height of specimen and interface on networks of shear bands are investigated numerically.
研究了围压、端面约束、试件高度及界面特性对剪切带网络形成的影响。
The pressure fluctuations in turbulent shear flows are investigated with the theory of spectral analysis.
本文应用谱分析理论研究了剪切湍流场中的压力脉动，包括功率谱、均方值等。
Based on the first-order shear deformation plate theory, axisymmetric governing buckling equations are derived for a functionally graded material circular plate subjected to in-plane pressure.
基于一阶剪切变形板理论，推导了功能梯度材料圆形板在边界面内均布压力作用下的轴对称屈曲方程。
The diameter, flow, shear rate, draw ratio, pressure difference and degree of profile in different configuration of capillary hole were calculated.
计算不同叶长，叶宽，孔数的喷丝板毛细孔的当量直径，单孔流量，剪切速率，喷头拉伸比，三叶异形孔压力降和异形度。
The results show that the frictions caused by the wall of shear box will influence the distributions of stresses in specimens and the normal pressure stresses on the shear plane.
结果表明，剪力盒壁摩擦力将会影响试验土样中的应力分布和剪切面上的正压应力值。
The normal pressure on the shear device has a defined influence on the lateral pressure and the influence is different for different soils.
剪切元件上的正压力对剪片侧面的侧压力有一定的影响，并因土质不同而变化。
The effects of the moisture content in polyester chip, the melt temperature and pressure, and the shear rate on the shear viscosity are discussed.
探讨了聚酯切片含水率、熔体温度、熔体压力、切变速率对熔体切变粘度的影响。
An additional axial preload tended to increase the pressure, the shear, and fiber strains essentially for all load scenarios.
特别在负荷方案中，一个附加的轴向前负荷可以趋向于增加压力、切应力和纤维强度。
Various vibration molding techniques, including oscillation packing injection molding, shear vibration injection molding, and pressure vibration injection molding were introduced.
对本课题组多年来进行的动态保压注射成型、剪切振动注射成型和压力振动注射成型研究进行了简要总结。
Using MTS Ultrasonic Measurement System, we studied the influences of water of saturation and pore pressure on velocities of compressional (P) and shear (S) waves in exposure rock specimens.
我们用MTS的超声波测试系统研究了地表岩样饱和水及孔隙压力对纵横波速度的影响。
In chapter 4, the influences of pore pressure on shear bands and on complete stress and strain curves have been modeled.
第4章对平面应变状态下应变软化岩石试件的孔隙压力效应进行数值模拟。
In chapter 4, the influences of pore pressure on shear bands and on complete stress and strain curves have been modeled.
第4章对平面应变状态下应变软化岩石试件的孔隙压力效应进行数值模拟。
应用推荐