Shaft Assembly male, female, washer, grease...
轴组件(轴，轴套，轴承，油脂…)。
The invention provides an output shaft assembly, an electric device and a screen wiper electric device.
本发明提供一种输出轴部件、电动机设备和雨刷电动机设备。
Lower device ~ lower casing, charger inlet, tail shaft assembly, tensioner, and with optional rotary detector and level switch.
下部装置——包括下部机壳、进料口、尾轴装配、张紧装置，并有旋转探测仪、料位开关供选配。
Ltd. also designs and manufactures various kinds of transmission shaft assembly, shaft coupling assembly as well as hydraulic pump assembly etc.
本公司还竭诚为客户设计，制造各类传动轴总成，联轴器总成，液压泵总成等以满足各界客户的需求。
An input disk (28), a clutch disk (38) and wave washers (56) are installed to an output shaft (12) to form an output shaft assembly (10) of a motor apparatus (90).
输入圆盘(28)、离合器圆盘(38)和波形垫圈(56)都安装到输出轴(12)以形成电动机设备(90)的输出轴部件(10)。
Main products are: the soft-core variety wire rope hose soft-shaft assembly manipulation of soft-warming breeze manipulating cables pushing cable car multifunctional hand brake.
主要产品有：各种软轴内芯、钢绳、软管、软轴总成、暖风机操纵软轴、操纵钢索、推拉索、汽车多功能手制动器。
Motorcycle clutch, single phase, starting motor, main shaft, main shaft assembly, gear, clutch, clutch plates, single carbon brush and carbon brush assembly, beyond the startup beads, set of cylinder.
摩托车离合器、单相器、起动电机、主付轴、主付轴总成、齿轮、离合器、离合片、单碳刷、碳刷总成、超越启动珠、套缸。
There are no bearings to fail or requirements for flexible couplings because its magnetized drum assembly is attached directly to the shaft.
没有轴承失败或弹性联轴器的要求，因为它的磁化鼓大会直接连接到轴。
After assembly, move the pump shaft with hand, it should be smooth and uniform without touch. Disassembly can be made with the steps contrary to above ones.
装配完成后，用手转动泵轴，没有擦碰现象，转动比较轻滑均匀即可，拆卸可按上述装配顺序相反的进行。
Lastly during assembly care is taken to avoid damaging the seals when passing over the keyway or performing bearing surfaces of the shaft.
最后，在组装过程中，当部件通过键槽时，注意避免损坏密封和轴的轴颈表面。
The entire rotating assembly shall be designed with sufficient rigidity and be balanced as a shaft and rotor assembly.
整个旋转总装都应该具有足够的硬度，并且能够与轴和定子总装之间协调运行。
The pump comprises mainly of pump body, cover, impeller, shaft, seal ring, intermediate support, sealing and suspension assembly, etc.
泵主要由泵体、泵盖、叶轮、轴、密封环、中间支架、密封和悬架部件等组成。
The entire rotating assembly shall be designed with sufficient rigidity for minimal shaft deflection at extreme pump operating conditions.
整个旋转总装都应该具有足够的硬度，即使在极端的泵运行环境下，所产生的轴偏差也是最小的。
Un-housed VCA shipped as Coil Assembly and Field Assembly, without shaft and alignment bushings.
非封装音圈调节器线圈，现场组装，船运不配自调整轴承和绝缘套管。
Rocker arm, Rocker arm shaft, Rocker assembly, Valve guide tube, Camshaft bearing Cap.
气门摇臂，摇臂轴，摇臂总成，气门导管，凸轮轴盖。
The rotor shall have an interference fit to the shaft and the rotating assembly shall be dynamically balanced to ISO 1940, G. 6.3.
定子应该通过压配合与轴结合在一起，旋转总装动态平衡应该符合ISO 1940， G.6.3标准。
Each tine assembly has a plurality of tines for aeration extending in a substantially radial pattern about the driven shaft.
每个打孔针组都含有多枚打孔针，这些打孔针围绕驱动轴以辐射形状排列充分地展开，可以为被打上孔的根系通气。
In the fourth chapter, the method of assembly feasibility analysis for shaft and hole feature was established.
第四章：建立轴孔要素装配可行性分析方法。
Automobile clutch in the engine and gearbox between the flywheel shell, with screw will be fixed in the clutch assembly after the plane of the flywheel, clutch gearbox output shaft is the input shaft.
汽车离合器位于发动机和变速箱之间的飞轮壳内，用螺钉将离合器总成固定在飞轮的后平面上，离合器的输出轴就是变速箱的输入轴。
Out in the shaft loaded oil ring groove or by centrifugal force along the axis of the oil drain off the surface, the oil flows back to the assembly after the pool, and thus play a role in sealing.
在轴上开出沟槽或装上油环，借离心力将沿轴表面外流的油甩掉，集结后流回油池，因而起到密封的作用。
Shipbuilding. shaft lines. couplings. forged flanges for assembly to taper - bore flanges.
造船工业。轴线。联轴节。装配镗圆锥孔凸缘的锻接法兰。
The interference taper assembly of the hub on the shaft is performed hydraulically and at ambient temperature, without dismounting the coupling.
轮毂与轴的对接锥形装配采用液压方式在环境温度下实现，而不需要对联轴节进行拆卸。
This paper presents experimental results for shaft seal assembly with three kinds of different support seats.
本文介绍了三组不同支座的轴密封部件试验结果。
The bearings at the both ends of the rotating shaft are spherical bearings, and the two bearing seats are well processed assembly parts.
两端的轴承是球面轴承，两个轴承座是已经加工好的组装件。
According to the requirement of the assembly of a shaft and a sleeve for coaxiality, a coaxial positioning system was presented based on the flexible decoupling beams and micro-vision technology.
针对偶件装配对同轴度的要求，提出了一种基于柔性解耦梁和显微视觉技术的同轴定位调整系统。
A shield assembly (40) includes the shaft (12) and a shield (40) rotatable with the shaft and positioned intermediate the impeller and the bearing assembly (26).
防护罩组件(40)包括轴(12)和可随轴旋转的防护罩(40)，防护罩位于叶轮和轴承组件(26)的中间。
In this paper, the correct assembly condition for the propeller shaft of an articulated vehicle is analyzed in the view of kinematics.
从运动学观点分析铰接式车辆传动轴的正确安装条件；
A shaft end pump should be included in the standard installation. The assembly space should be considered at site. Shall the installation not meet the requirement, please contact with the supplier.
标准配置含轴端泵，现场应预留安装空间，若不能满足安装要求，请与厂家联系。
An assembly step matching the shaft shoulder of the mainshaft is positioned on the shaft sleeve and a fixed gap forms between the shaft sleeve step and the water-tight plate.
轴套上设有与主轴轴肩配置的装配台阶，轴套台阶与水密封板之间形成有固定的间隙。
An assembly step matching the shaft shoulder of the mainshaft is positioned on the shaft sleeve and a fixed gap forms between the shaft sleeve step and the water-tight plate.
轴套上设有与主轴轴肩配置的装配台阶，轴套台阶与水密封板之间形成有固定的间隙。
应用推荐