IrDa chips incompatible with the serial driver have their own device drivers.
与串行驱动器不兼容的IrDa芯片有自己的设备驱动程序。
If this happens for you, read the section about configuring the USB serial driver in the Qt Documentation.
如果出现这种情况，请阅读Qt文档中关于如何配置US B串口驱动的一节。
The design of driver and the development of serial driver are important in constructing embedded system.
驱动程序及串口驱动的开发和设计是构建嵌入式系统的重要组成部分。
The legacy serial driver that drives this board's UART channels can send and receive data from the BlueZ UART transport driver.
这个母板的UART通道使用的传统串行驱动程序可以从BlueZ UART传输驱动程序上收发数据。
You will need the device for which you are writing the driver and a null-modem (serial) cable for remote debugging.
需要有一个正在为其开发驱动程序的设备，以及一根串口线来进行远程调试。
Examples of devices at this layer include the SLIP driver over a serial interface or an Ethernet driver over an Ethernet device.
例如，包串口使用的SLIP驱动程序以及以太网设备使用的以太网驱动程序都是这一层的设备。
These drivers include Serial port, LCD, Touchscreen, and I2C bus driver which is used to control keyboard.
其内容包括串口驱动、LCD驱动、触摸屏驱动及控制键盘的I2C总线驱动。
RS485 serial programming driver code, suitable for low-level driver development using RS485 projects.
说明：RS485串口编程驱动代码，适用于采用RS485进行底层驱动开发的项目。
SERCOS (SErial Real-time Communication System) is the serial real-time communication fieldbus between digital controller and servo-driver.
接口是数字控制器与伺服驱动器间的串行实时通信总线。
Meanwhile long-distance reading and setting of the pump-module LD driver can be achieved by the design of serial device circuit control system.
具有串口通信电流源控制系统，能够实现对驱动电流值的远程读取与设置。
The program is written based on my self-ST7920 LCD controller serial LCD driver.
本程序是本人自写的基于ST7920液晶控制器的串行LCD驱动程序。
As a constituent of the monitor programs, a method of multi-threading serial communication to control the driver low-level of the RF system in SSRF is introduced.
作为高频系统监控程序的一个组成部分，本文采用了多线程串口通信的方法实现了对SSRF高频系统激励电平的控制。
Several key focus of the driver and the realization of transplantation, including the serial port, LCD display and power management.
重点分析了几个关键驱动程序的实现和移植，包括了串口、LCD显示器及电源管理。
The design adopts serial control mode, in this case there are only two controlling lines between the single chip microcomputer system and the driver of the step motor.
单片机对步进电机的控制有串行控制和并行控制两种方式。本设计采用的是串行控制方式，此方式下单片机控制系统与步进电机驱动器之间只有两条控制线。
This serial ports driver which has been applied and tested for a long time runs steadily in the whole system.
该串口驱动经过长时间的应用和测试，在整个系统中运行稳定。
Then mainly expatiates RTL8019AS Ethernet controller driver and serial interface driver of embedded communication platform; Finally, discusses the application program development and driver testing.
然后重点阐述了嵌入式通信平台RTL8019AS以太网控制器和串口驱动程序的设计方法，并分析了驱动程序的调试方法；
Then mainly expatiates RTL8019AS Ethernet controller driver and serial interface driver of embedded communication platform; Finally, discusses the application program development and driver testing.
然后重点阐述了嵌入式通信平台RTL8019AS以太网控制器和串口驱动程序的设计方法，并分析了驱动程序的调试方法；
应用推荐