Select the assembly name from the list that appears.
从显示的列表中选择程序集名称。
To locate it, select the component in the assembly editor.
要定位此属性，请在组装编辑器中选择对应的组件。
To create a Process component, open the assembly editor, select and drag Process to the editor, rename the component to OrderProcess.
创建Process组件，打开装配编辑器，选择process并把它拖到编辑器中，把这个组件改名为OrderProcess。
To create a Human Task component, open the assembly editor, select and drag Human Task to the editor, and rename the component ManagerApproval.
创建HumanTask组件，打开装配编辑器，选择 Human Task并把它拖到编辑器中，把这个组件改名为 ManagerApproval。
Right-click the canvas in the assembly diagram and select Test Module.
在组装关系图中右键单击画布并选择Test Module。
If you want to test all of the components of your module, then you can right-click the assembly editor canvas and select test module.
如果您需要测试模块的所有组件，则可以右键单击组装编辑器画布，并选择Test Module。
To clean up the assembly diagram, drag the components around to match Figure 31, or just right-click the editor and select LayoutContents.
若要清理组装关系图，可四处拖动组件以匹配图31，或者只需右键单击编辑器并选择Layout Contents。
Right click the canvas in the assembly diagram and select Test Module.
在组装关系图中，右键单击画布并选择Test Module。
Right-click on the export on the Assembly Diagram and select Test Component (see Figure 16)
在组装关系图上右键单击导出，并选择TestComponent（参见图 16）
Within the assembly diagram, select the InsuranceQuote component and right-click it.
在组装关系图中选择Insurance Quote组件并右键单击。
Select the import in the assembly editor and go to the Properties TAB at the bottom of the tool.
在组装编辑器中选择导入，并转到该工具底部的Properties选项卡。
In the assembly editor, you can right-click on a component, and select add - reference to add new references.
在组装编辑器中，您可右键单击某个组件，并选择add-Reference以添加新的引用。
Open the LoanProcess_Module assembly diagram, and then select the component reference of the LoanProcess component.
打开 LoanProcess_Module 组装关系图，然后选择LoanProcess组件的组件引用。
Select the Standalone references icon and drag it anywhere on the Assembly Editor as shown in Figure 41.
选择Standalonereferences图标，并将其拖至assemblyEditor中的任何位置，如图41所示。
Retest the EJB via the import: right-click on the TemperatureEJB import on the Assembly Editor canvas and select test Component.
通过导入重新测试e JB：在组装编辑器画布上右键单击TemperatureEJB导入，并选择Test Component。
Problems existed in using combined jig to assemble airplane are analyzed and the principle of how to select integral structure configuration of jig for airplane assembly is introduced.
分析归纳了飞机装配中采用组合式型架存在的问题； 介绍了飞机装配中型架总体结构形式的选择原则；
Carefully select the default resources to compile with the main assembly.
请小心选取要和主要组件一起编译的预设资源。
Select this check box to sign the assembly and create a strongly named key file.
选中此复选框为程序集签名并创建强名称密钥文件。
According to the experiment ask, Change the Transmission Ratio, select dimensions of all key parts and put into manufacture, assembly and debugging.
按照实验的要求，重新分配了各级传动的传动比，确定了各关键部件的尺寸并加以制造、安装与调试。
According to the experiment ask, Change the Transmission Ratio, select dimensions of all key parts and put into manufacture, assembly and debugging.
按照实验的要求，重新分配了各级传动的传动比，确定了各关键部件的尺寸并加以制造、安装与调试。
应用推荐