The crown can be controlled by optimum distribution of rolling force.
轧制力的合理分配可以有效控制板凸度。
Balancing system provide proper rolling force with rolling down system.
平衡缸系统配合压下系统提供合适的轧制力。
The artificial intelligence method to setup and control rolling force is researched.
研究了轧制力设定控制的人工智能实现方法。
The theory and measurement method of measuring the rolling force are correct and practicable.
用该传感器测量轧制力是正确、可行的。
Abstract: The artificial intelligence method to setup and control rolling force is researched.
文摘：研究了轧制力设定控制的人工智能实现方法。
It can measure the rolling force exactly in the course of single-wedge and multi-wedge rolling.
该系统可以在线准确测出单楔与多楔轧制过程中轧制力变化规律。
On the basis of theoretic analysis and experiment, the new rolling force model has been developed.
通过理论推导和现场实验相结合，建立了新的轧制力模型。
The dynamic rolling force P on line was tested by electronic measurement combined with photoelasticity.
应用光电组合新方法，成功地测算了在线动态轧制力部。
Plant mills' bearing is one of the important parts on mill. It directly bears rolling force when mill works.
中厚板轧机轴承是轧机的关键零部件之一，直接承受轧机运行中产生的力。
And its outstanding virtue is the minimal fluctuation of the rolling force produced by the rolling mill structure.
其最突出的优点是由轧机结构引起的轧制力波动最小。
This paper introduced the development of the online intelligent detecting system of rolling force by LabVIEW software.
本文介绍了一个利用虚拟仪器技术开发的轧制力在线智能监测系统。
So, the casting speed plays an efficient role in readjusting the molten steel surface level in pool and rolling force.
铸轧速度是调节熔池液面高度和轧制力的有效手段。
Have excellent lubrication performance, effectively reduce the rolling force, reduce roll wear, avoid sticky roll show.
具有优异的润滑性能，有效降低轧制力，减少轧辊磨损，避免粘辊显现。
Based on practical data trained by the neural network, the model enables to give better prediction result of rolling force.
网络在多次训练后对生产中的历史数据进行了轧制力预报，达到了较高的预报精度。
This paper presents an artificial neural network model to predict the rolling force to control hot-rolled strip strip thickness.
研究了热轧板带厚度控制中轧制力预报环节的局部逼近神经网络实现方法。
The result of on-line application indicated that rolling force model has good precision of prediction with an error less than 5%.
现场在线应用结果表明：给出的轧制力模型具有良好的预测精度，预测误差可以控制在5%以内。
In the test, the computer data collection system has been applied to measure rolling force, torque and power in rolling procession.
实验中对轧制压力、轧制扭矩、轧制功率进行了测试，并将单头和双头模具所测得的结果进行了比较与分析。
The reasons of rolling force and torque reduction are discussed. Also the simplified formulas of rolling force and torque are derived.
文中分析了其大幅度降低的原因，并推导出求轧制力和力矩的简化公式。
By comparison with actual measurement parameters, this conesquence is confirmed to be more accurate in the prediction of the rolling force.
通过与现场实测数据的比较，证明了本解法能更准确的预报冷轧薄板的轧制力。
With the monitoring system, the attached type ergometric sensor can be used for the online rolling force monitoring, which proves nice effect.
最后又结合轧机工况监测系统，使用附着式测力传感器对轧制力进行在线监测，证明具有较好的使用效果。
Because of its unique ability to process information, the technology of neural networks is very appropriate for the computing of rolling force.
神经网络技术以其特有的信息处理能力，为轧制力的计算提供了一条很好的途径。
Distribution of temperature, equivalent plastic strain and radial and axial rolling force have been quantitatively analyzed in the whole process.
定量分析了整个轧制过程环件内的温度、等效应变、双向轧制力的分布和演化情况。
For improving the precision of prediction of rolling model, a new method using artificial neural networks of rolling force modeling is put forward.
为了提高轧制力模型预报值的精度，提出了一种基于人工神经网络的轧制力建模新方法。
The algorithm is able to adjust the schedule to make the strip thickness error less than set one by modifying the limit coefficient of rolling force.
该算法通过调整轧制力限制系数来调整约束条件使得最后道次的出口厚度与目标厚度的偏差小于给定误差，并同时获得优化的轧制规程。
On the basis of the limited conditions, entry thickness, exit thickness, rolling speed, tension, rolling force and rolling torque, etc. are calculated.
根据极限条件，计算出入口厚度、出口厚度、轧制速度、张力、轧制力、轧制力矩等。
Two-Stand Hot reversing mill is a reversing mill, two stand roll can realize roughing phase and finishing phase, large-scale rolling force, good shape.
双机架炉卷热轧机是典型的往复式轧机，它的两个机架实现粗轧和精轧，轧制压力大，板型精度高。
The traditional rolling force model of 4-stand tandem cold strip mill at Anshan Iron and Steel Corporation was analyzed, and some defects were found out.
分析了鞍钢冷轧厂4机架冷连轧机轧制力模型，指出了其存在的主要缺陷，并提出了改进方案。
The specific rolling force distribution was obtained by simulation and the calculated results of rolling force are in good agreement with the measured ones.
模拟结果证实了应用显式动力学弹塑性有限元法模拟双金属复合板轧制的可行性，且计算所得轧制力与实验结果吻合较好。
Using three dimensional fluxional function, the rolling force and energy parameters of oval round pass sequences for hot continuous bar rolling were analyzed.
采用三维流函数法对棒材热连轧时的椭圆-圆孔型系统进行了力能参数的解析，其结果与实测结果符合很好。
Using three dimensional fluxional function, the rolling force and energy parameters of oval round pass sequences for hot continuous bar rolling were analyzed.
采用三维流函数法对棒材热连轧时的椭圆-圆孔型系统进行了力能参数的解析，其结果与实测结果符合很好。
应用推荐