Based on the former research, the software of the design and diagnosing for the rod pumping system is developed.
基于上述理论研究，开发了有杆抽油系统设计与诊断软件。
Basic parameter database of rod pumping system is built, the access to database by means of program is accomplished.
建立了有杆抽油系统基本参数数据库，并实现了对数据库的程序访问。
In addition, a method for checking the reliability of the failure data of rod pumping system is expounded with field examples.
还通过实例说明了有杆泵抽油系统检泵故障数据的可靠性分析方法。
In the light of short production cycle of rod pumping Wells in Shengtuo Oilfield, the causes of the well failure are investigated twice.
针对胜坨油田有杆泵井检泵周期比较短的突出问题，进行了两次有杆泵井失效原因调查与分析。
Using the computer technology to monitor and evaluate the condition of rod pumping system is important for improving the efficiency of oil production.
结合计算机软件技术对其运行效率进行监测评价并在此基础上及时给出优化调整方案，是提高石油开采效益的重要途径之一。
At present, heavy oil or extra heavy oil is produced by means of thermal oil recovery or rod pumping, which are low efficient, energy consuming and short in production life.
目前，稠油或特稠油一般采用热力及有杆泵进行开采，这种生产方式效率低、能源消耗大，且设备运行寿命短。
The design philosophy and method for equal stress ratio of pumping rod are proposed and the corresponding software for optimization design of rod pumping parameters is compiled.
文中还提出了抽油杆等应力比的设计思路和方法，并编制了相应的机抽参数优化设计软件。
The parameter data-base of the beam pumping unit and the newly energy-saving pumping unit is established, which lay a solid foundation for the simulation of the rod pumping system.
建立了游梁抽油机和新型节能抽油机的参数数据库，为实现对有杆抽油泵系统的仿真研究奠定了基础。
The rod pumping is the predominance mechanical recovery mode in world petroleum production, the system dynamical simulation is the base of system efficiency analysis and optimum design.
有杆泵抽油是世界采油工程中一直占主导地位的机械采油方式，系统动态模拟是系统效率分析和优化设计的基础。
Rod pumping oil recovery system is applied widely, the optimal method was usually used to enhance the efficiency, but it is easy to ignore that the electromotor matches other fixtures rationally.
有杆泵往复抽油方式常采用机、杆、泵优化的方法来提高系统的整体效率，但易忽略电动机与其他设备的合理匹配。
Appropriate machining, rolling rolling make quantitative, and ford All or variant processing, pumping rod or line stretching.
适切削加工，做定量压延滚牙性，用于卯合或变型加工，抽伸棒或线。
Eddy current, magnetic leak, magnetic particle and ultrasonic test are the main methods used for pumping rod test.
目前，对抽油杆的自动探伤主要有涡流、漏磁、磁粉及超声方法，各有其优缺点及适用范围。
The main drive chain and the bearing chain divide the polished rod load into reverse pumping load and equilibrium load.
主传动链与承载链将悬点载荷分解为换向抽汲载荷与平衡载荷。
Compared with conventional beam pumping unit, the swing-rod beam pumping unit can reduce the maximum crank axle torque markedly, reduce and even eliminate negative crank axle torque.
同常规型游梁式抽油机比较，该机型可以显著降低曲柄输出轴的最大扭矩，减小甚至消除负扭矩，在降低能耗的同时改善了减速箱的受力状况。
Then, in view of the actual operation for pumping problems such as the belt, broken rod, rod case of cards brake and so on in a depth discussion and analysis, and proposed solution to the problem.
再针对抽油机在实际运行中出现的问题，对断带、断杆、抽油杆遇卡和刹车等进行深入的讨论与分析，提出问题的解决方案。
The influence of dynamic thermal effect induced by optical pumping of YAG crystal rod in a pulsed solid laser on the wave front of the output laser beam is studied in this paper.
本文研究了脉冲固体激光器的YAG激光棒光泵浦动态热效应对激光波面的影响。
The identification of down-hole dynamometer card is the key to making the diagnosis expert system for pumping with rod.
井下示功图的自动识别是建造有杆抽油工况诊断专家系统的一个技术关键。
CYBS series anti sand travelling barrel rod pumps were used on 4 Wells in Wennan Oilfield to test their performance of sand control and slush pumping.
采用CYBS系列动筒式防砂卡抽油泵，在文南油田不同井况的4口井中进行了防砂卡抽泥浆工艺的生产试验。
As its structure character of beam pumping unit, vibration and noise happen on the joint of connection rod head and beam during operation.
游梁平衡抽油机由于其自身结构特点，在运行过程中，连杆上接头与横梁连接部分经常会出现振动和响声。
The control rod string which is consisted of pumping rod and controller is tripped into the release string.
抽油杆与控制器组成的控制杆柱下入到丢手管柱内，控制杆柱上部与杆式泵的进油孔相连。
The ray tracing and Monte Carlo method are applied to calculate the distribution of deposited pumping energy within a rod amplifier of the high power solid state laser system.
建立了用蒙特卡罗和光线跟踪法计算高功率固体激光系统棒状放大器能量沉积分布的模拟程序。
The temperature field and warming process of the transient and steady state in the laser rod by symmetrical trigonal side-pumping were simulated using the finite element analysis method.
用有限元法计算模拟了三角均匀分布侧面泵浦结构激光棒瞬态温升过程及稳态温度分布情况。
Wire rope and assembly pulley on the flexible pumping units replace balance beam and connecting rod on regular pumping units.
柔性抽油机结构上使用钢丝绳和滑轮组替代了常规抽油机的游梁和连杆。
The common faults during oil pumping rod inspection are analyzed, the reasons that cause them and the solving methods are discussed.
对抽油杆检测中发现的常见不合格项进行了分析，探讨了形成原因和解决方法。
The common faults during oil pumping rod inspection are analyzed, the reasons that cause them and the solving methods are discussed.
对抽油杆检测中发现的常见不合格项进行了分析，探讨了形成原因和解决方法。
应用推荐