Then hand-tighten the pivot rod’s retaining nut enough that the rod can still move up and down.
然后手动旋紧螺母但保证旋杆能上下移动。
Install adjusting nut to the tensioner rod and adjust parking brakes.
将调整螺帽安装到拉伸器杆并调整手刹车。
To do so you need to loosen the top 3/8 nut and back it off without unthreading the threaded rod from the spider .
压缩弹簧。要这样做，就要松开顶部3/8英寸螺母并拿开，不要旋松星轮上的螺纹杆。
The hoisting jack calls the mechanical hoisting jack, is by the manpower through the screw vice-transmission, the screw rod or the nut sleeve achievement goes against lifts.
液压千斤顶又称机械式千斤顶，是由人力通过螺旋副传动，螺杆或螺母套筒作为顶举件。
Through the failure analysis of connecting bolt of down rod, it points out that it is not correct to put the thinner nut outer side if the double nut anti-loose method is adopted.
通过对游梁式抽油机对接式连杆下接头连接螺栓的失效分析，指出了采用双螺母防松时，将薄型螺母放置在外侧是不恰当的。
Because the mechanism replaces a traditional screw rod and screw nut mechanism, the rotary furniture has simple structure, stable rotation and low cost.
用这种机构代替传统的螺杆螺母机构。可使旋转类家具结构简单，旋转平稳，成本降低。
"Transfer mode" used motor oil transfer mode, there is no overload protection function, the load increased, the four tension rod threads, thread nut transfer mold damage.
“调模”使用油马达调模，没有过载保护功能，负载加大后，四根拉紧杆螺纹、调模螺母螺纹会损坏。
The injection moulding device comprises a substrate nut (2), a process screw rod (4) screwed into the substrate nut (2), and two positioning nuts (1).
注射成型装置包括基体螺母(2)及旋入基体螺母(2)中的工艺丝杆(4)和两个定位螺母(1)。
Disclosed is an orthopedic vertebra reduction device which consists of a reduction nut (1), a reduction rod (2) and a fixed rod (3).
一种骨科椎体复位装置，它是由复位螺母(1)、复位杆(2)、固定杆(3)组成。
One end of a connecting rod on both sides of the screw nut is connected with the pin of a sliding chassis, and the other end is hinged with the screw nut.
螺母两侧的连接杆一端与滑动机架上的销轴连接，另一端与螺母铰链。
Presents the following viewpoints:the radio between the height of the nut for boiler hanger rod and the diameter of screw shall not be less than 1.
主要提出以下观点：锅炉吊杆用螺母的高度与螺纹公称直径之比不宜小于1。
The support nut is screwed onto the support rod against the bias of the spring to secure the window in its closed position.
支撑螺母克服弹簧的偏置旋紧到支撑杆上来保证车窗位于其关闭位置。
On the rod body, a washer is sheathed with the part which is corresponding to the part between the tray and the screw nut of each compressing piece.
杆体上对应于每套压紧件中的托盘和螺母之间处均套装一个垫圈。
A fastener screw rod-nut disassembly machine pertains to the technical field of building construction tools.
扣件螺杆-螺母拆卸机，属于建筑施工工具的技术领域。
A fastener screw rod-nut disassembly machine pertains to the technical field of building construction tools.
扣件螺杆-螺母拆卸机，属于建筑施工工具的技术领域。
应用推荐