This paper demonstrates residual stress of induction quench parts and personal views about stress distribution of flange corner heat treatment, truck half axle material and depth of hardened layer.
论述了感应淬火零件的残余应力形态，并对载货车半轴的材料、硬化层深度及法兰圆角淬火层分布提出了个人见解。
The distribution of fluid residual pressure of Mesozoic strata in Ordos basin is studied based on the equilibrium depth method.
利用平衡深度法研究了鄂尔多斯盆地中生代地层的流体剩余压力分布特征。
This technique used in the present analyzer can non-destructively measure light metals' residual stresses with depth resolution, such as beryllium, by altering measuring and evaluating method.
该方法利用现有仪器，通过改变测定技术和计算方法，可以无损测定铍等轻金属制品表面残余应力及沿层深的分布。
The research result shows the location accuracy by the method is better and improves more than original location result in residual error, evaluated error, epicenter distribution and focal depth.
研究结果初步表明该方法定位精度比较高，无论在残差、测定误差、震中分布还是震源深度方面，都比原来定位结果有较大改进。
The width and depth of laser transformation hardening zone and residual stress distribution were measured experimentally.
实测了激光相变硬化区的宽度和深度及残余应力分布。
Test shows that the depth of residual compressive after chemical heat treatment is correspondent with that of diffusion layer.
试验表明，化学热处理后残余压应力的深度往往与渗层深度相一致。
Compared with the dry-grinding, the surface compress residual stresses of the hardened layer under wet-grinding is increased, but its depth of hardened layer reduces about 30%.
与干磨相比，湿磨硬化层表面残余压应力有所提高，但其硬化层深度减少了约30%。
Subtracting the gravity anomalies caused by density anomalies from the observed Bouguer anomalies, we inversed the depth of Moho of northwestern China by using the residual anomalies.
在从观测布格重力异常中扣除上述密度异常引起的重力异常后的数据基础上，直接反演了中国西北区域莫霍界面的深度。
But its maximum compressive residual stress and influencing depth reduces.
但其最大残余压应力值及应力影响深度有所降低。
The paper does an in-depth research on the numerical model of pyrolysis process of the materials with volatile residual layer by using pre-evaluation iteration method.
采用偏微分数值模型，使用热解界面预估循环迭代的方法，对存在可变残留层材料的热解过程进行了详细研究。
The residual intensities both the uniform wear and non-uniform wear of casings have the reverse proportions with the abrasion depth on casings.
对于非均匀磨损，其剩余抗拉强度与磨损长度之间的关系均近似服从指数分布。
The simulation on medium frequency induction hardening process of crankshaft in 6110 engine is carried out by using FEA software ANSYS with hardening depth predicted and residual stress calculated.
利用A NSYS有限元分析软件，进行了6 110钢曲轴的中频感应淬火过程的模拟计算，并预测了淬硬层的深度，计算了淬火后的残余应力分布。
The distribution of residual stress along depth gained through layer-by-layer measuring method after chemical etching is in line with that measured by multi-wavelength method.
化学蚀刻后逐层测试所得应力沿深度分布与用多波长法测试结果趋势一致，大小略有差异。
The distribution of residual stress along depth gained through layer-by-layer measuring method after chemical etching is in line with that measured by multi-wavelength method.
化学蚀刻后逐层测试所得应力沿深度分布与用多波长法测试结果趋势一致，大小略有差异。
应用推荐