Measurement should be done as the 2. C. the average dry thickness must not less than the required thickness.
应按照第2 .C部分的要求进行测量。平均干燥厚度必须等于或大于业主要求后度(单位：密耳)。
Slabs are heated in reheating furnaces and rolled to the required thickness in hot-rolling mills. The final product is flat steel in coils and thick plates.
将板坯置入加热炉内加热，并在碾轧机上轧成所需的厚度。最终产物是介于线圈和厚板之间的产品-扁平钢板。
Because stainless steel in China is NOT solid stainless steel it is a sandwich material. which is then rolled out to the required thickness but a quick magnet test will reveal all.
因为中国的不锈钢不是结实的不锈钢，而是夹层结构。虽然按照要求厚度制成，但是用磁铁测试法就可以一探究竟。
Because stainless steel in China is NOT solid stainless steel it is a sandwich material. which is then rolled out to the required thickness but a quick magnet test will reveal all.
因为中国的不锈钢并不是实打实的不锈钢，而是一种夹层材料，被压成所需的厚度。
Read and interpret blueprints and specifications to determine type and thickness of glass, frame, installation procedure and materials required.
阅读和解释蓝图和规格，来确定玻璃，框架，安装程序和所需材料的类型和厚度。
The raw data output from the measuring equipment for surface roughness and coating thickness must be attached to all required documentation.
对所需的所有文档还必须附上测量设备测量表面粗糙度和涂层厚度时输出的原始数据。
Construction of the formwork and preparation of the metal reinforcement for shells required particular care and accuracy because of their limited thickness.
由于壳体的厚度有限，壳体的金属能加工制备与模板建造需要特别细心与精确。
If the day after due to the stiffness of the material required to change the material thickness, may lead to male into female die.
如果日后由于材料刚度的需要要求改变材料厚度，可能导致要将阳模转换为阴模。
As the thickness of blank increases, when the special products was required in thickness, it may be thought of graded hot-pressing.
但随板坯厚度(层数)的增加，即在制造厚度有特殊要求的产品时，应考虑采用分步热压法。
If the required paint film thickness has not been achieved, the additional coats should be applied till the specified thickness is attained.
如果未达到要求的湿膜厚度，应覆涂直到满足指定的湿膜厚。
Precision measurement of blade wall thickness along the common normal of inner and exterior surfaces is required to guarantee the reliability of air engine.
为保障航空发动机的可靠性，要求精确测量发动机叶片不同界面处的内、外表面法线方向的厚度。
The required finished coating thickness shall be specified by the purchaser. The specified thickness should not exceed the maximum recommended by the coating manufacturer.
业主需要确定涂层的厚度，但是厚度不应超过涂层生产商的建议厚度。
The thickness of glutenite body required for storage layers and hydrocarbon migration trace was close, which was very different from thickness without migration trace.
同时在仓储层中显示油气成藏和有油气运移痕迹所要求的砂砾岩体厚度是相近的，而与无油气运移痕迹的砂砾岩体厚度有明显的差别。
Foams can be used where thick sections are required to achieve rigidity, and can accommodate large wall thickness variations.
泡沫材料可用厚截面达到所需的刚度，可实现大的壁厚变化。
Where multiple layers of coating are required to achieve the specified thickness, each layer shall be applied at right angles to the preceding layer.
多层涂层应达到规定的厚度，每一层应与前一层成直角。
The paper analyzed the thickness difference in typical objects, and thickness tolerance required for different sensitivity classes.
本文分析了典型工件的厚度差，以及不同灵敏度级别的厚度宽容度。
Damp earth may be expected to act in a similar manner, although about 50 percent greater thickness would be required.
预期湿土也能起到同样的作用，不过这时厚度约需增加50%。
The extra thickness enables the car to achieve an ultra-stiff torsion and flex setting required for high-competition foam racing.
额外的厚度，使汽车达到超扭转刚性和柔性设置所需的高竞争的泡沫赛车。
The final choice of threads would depend on fabric thickness garment style and required seam strength.
7一件衣服最终使用那一种缝纫线，应根据面料的厚度、服装的款式及线缝的牢度而定。
The final choice of threads would depend on fabric thickness garment style and required seam strength.
7一件衣服最终使用那一种缝纫线，应根据面料的厚度、服装的款式及线缝的牢度而定。
应用推荐