When the total cycle pump gear shift operation, the flow of the slip road ratio unchanged.
当总循环泵变速运行时，各个支路的流量分配比例保持不变。
When installing coupling hammer shall not be used, in order to avoid damage of the gear pump gear And other parts.
安装联轴器时不得用锤敲打，以免伤害齿轮泵的齿轮等零件。
The manufacturing process for P/M low pressure oil pump gear, conditions of stand testing and technological and economic results have been introduced.
介绍了粉末冶金低压油泵齿轮的制造工艺、台架试验情况及应用的技术、经济效果。
Pump wear parts are mainly drive shaft and bushing, passive gear center hole and shaft pin, pump shell lumen and gear, gear face and pump cover, etc.
齿轮泵的磨损部位主要有主动轴与衬套、被动齿轮中心孔与轴销、泵壳内腔与齿轮、齿轮端面与泵盖等。
Pump is the drainage and back into the groove of reasonable design, is a gear in the work under the minimum torque force, so the bearing load is small, wear small, pump with high efficiency.
输送皂角泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
Internal gear pump structure and other gear pump structure similar to, mainly by the outer rotor and rotor, pump shaft, pump body, the front cover, bracket, sealing device, bearing, etc.
内啮合齿轮泵的结构和其他齿轮泵结构类似，主要由外转子、转子、泵轴、泵体、前盖、托架、密封装置、轴承等组成。
Rationally define the work gear pump speed, gear and the axis of rotation to avoid engaging resonance frequency, can prevent noise intensified.
合理确定齿轮泵的工作转速，使齿轮与轴的转动避开啮合共振频率，可以防止噪声加剧。
If the first gear pump operation, or long-term idle after use, preferably in small load or no-load circumstances Xianpao One hour.
齿轮泵若是第一次运行，或长期闲置后再使用，最好在空载或小负荷情况下先跑合一小时左右。
The gear pump seals the selection principle is not high demand, for the occasion, but by experience, not to replace timely selection.
齿轮泵密封垫的选用原则是，对于要求不高的场合，可凭经验选取，不合适时再更换。
Internal gear pump is the small gear wheel, the big gear for driven wheel, in work big gear with small gear cocurrent rotation.
内啮合齿轮泵中的小齿轮是主动轮，大齿轮为从动轮，在工作时大齿轮随小齿轮同向旋转。
High viscosity gear pump does not generate pressure, it is only the output flow. Pressure is low or no pressure, high viscosity gear wheel pump don't inhale the liquid or leakage is serious.
高粘度齿轮泵并不能产生压力，它只是输出流量。压力低或无压力，说明高粘度齿轮泵没有吸入液体或泄漏严重。
Check valve and relief valve on the output of the gear pump tube had better install a check valve.
止回阀与安全阀在齿轮泵的输出管路上最好安装一个止回阀。
Gear pump with the direction of rotation into and out in line with the oil mouth.
齿轮泵的旋转方向要与进、出油口相符。
In addition, the camshaft has an eccentric to operate the fuel pump and a gear to drive the ignition distributor and oil pump.
此外，凸轮轴还带动一个驱动燃料泵的偏心轮和一个带动分电器和油泵的齿轮。
The product is applied to medium, high-pressure gear pump, ram pump, vane pumps, etc.
产品主要应用于中、高压齿轮油泵、柱塞泵、叶片泵等。
Internal gear pump has two kinds of tooth profile namely: involute profile and cycloidal tooth profile.
内啮合齿轮泵有两种齿形即：渐开线齿形和摆线齿形。
Use of helical gear in gear pump is an effective measure, which can reduce the mechanical voice and flow pulse.
齿轮油泵采用斜齿轮是降低机械噪声和减小流量脉动的一种有效措施。
According to the volume oil formula of the straight gear pump, the volume oil formula of the helical gear pump is got and the helix Angle no trapping is found.
利用直齿齿轮泵的困油容积变化公式，求出了斜齿齿轮泵的困油容积变化公式，得到了斜齿齿轮泵不发生困油的螺旋角。
With the piston pump, diaphragm and gear pumps is different is that single-screw pump can be used for pharmaceutical filling and measurement.
与柱塞泵、单螺杆泵及齿轮泵不同的是，单螺杆泵可用于药剂填充和计量。
The prominent characteristics of gear pump in application to flow metering and fluid transportation were introduced in this article.
介绍了齿轮泵用于流量计量和流体输送时所具有的突出特点。
This paper introduces the criterion and some noted problems of gear design for internal gear pump.
本文介绍了内啮合齿轮泵齿轮设计的准则及应注意的几个问题。
The addendum coefficient is an important parameter in the designing the gear, and to affect the discharge characteristic of compound gear pump.
齿顶高系数是设计齿轮时的重要几何参数，也是影响复合齿轮泵流量特性的重要参数之一。
The method was discussed for how to integrate optimizing and building model with finite element analysis on 3D development and analysis of outer-tooth gear pump through UG design platform.
探讨通过UG设计平台，如何将优化程序、3D模型建立、有限元分析等，有机集成于外啮合齿轮泵齿轮3D设计和分析中去。
Flexible set cycloid gear pump rotor pump vane pump with the advantages of a similar volume than pump more than 10% efficiency.
柔性摆线转子泵集齿轮泵与叶片泵优点于一身比同类容积泵的效率提高10%以上。
The analysis results provide the necessary bases which are benefited for the design and improvement of new screw pump synchronous gear.
计算分析结果为新型螺杆泵同步齿轮的设计和改进提供了必要的依据。
Comparing with involute gear pump, the instant displacement is in direct proportion to the angular velocity of the gear and stable without pulsation.
对比渐开线齿轮泵，单圆弧齿轮泵的瞬时排量与齿轮角速度成正比，且稳定，无脉动。
This article will discuss the design of compensating groove in external gear pump by analyzing the gearing characteristics.
该文主要通过分析齿轮的啮合特点来探讨啮合齿轮泵卸荷槽的设计。
The interlaced gear pump is designed on the basis of analysing flow and pressure pulses.
本文在分析齿轮泵的流量脉动和压力脉动的基础上，设计出一种错齿齿轮泵。
High viscosity gear pump does not generate pressure, it is only the output flow.
高粘度齿轮泵并不能产生压力，它只是输出流量。
High viscosity gear pump does not generate pressure, it is only the output flow.
高粘度齿轮泵并不能产生压力，它只是输出流量。
应用推荐