The system is composed of industrial PC, DMC300 motion controller, discharge status checking card, A/D card, I/O card and pulse power.
该系统由工业PC，DMC300运动控制器，放电状态检查卡，A/D 卡，I/O 卡和脉冲电源组成。
Pulse power density directly influences ablation crater depth.
脉冲功率密度直接影响烧蚀凹坑深度。
A semiconductor laser array with pulse power of 100w was made by utilizing the solder.
利用这种焊料研制出脉冲功率达100w的半导体激光器列阵。
Moreover, applications of pulse power suppliers in other fields were briefly introduced.
简单介绍了脉冲电源在其它领域中的应用。
Formulas are derived for the ensemble average of the pulse power and the RMS pulse width.
得到了在光纤中传输的脉冲光功率的系综平均值和输出脉冲宽度的均方根值的近似解析公式。
The circuit schematic diagram of the high voltage pulse power supply is designed by author.
作者设计了脉冲高压电源的电路原理图。
The circuit parameters affecting the increase of peak pulse power of the device have been found.
找出了影响提高器件脉冲峰值功率的电路参数。
The keystone is pulse power control components developed independently and software based on IPC.
着重点在自主开发的脉冲电源控制部件和基于IPC的软件上。
Some experiments and applications show that the portable pulse power supply is stable and reliable.
实验和应用表明，该小型脉冲电源具有较好的稳定性和可靠性。
When Q-switch and gain switch were applied the peak pulse power was increased and pulse width decreased.
利用增益开关和Q开关双机制作用，压窄了调Q脉宽，提高了输出功率。
An intelligent control system of high current low voltage pulse power supply is introduced in this paper.
介绍了针对大电流、低电压的脉冲电源的智能控制系统。
Now pulsewidth modulating technology is widely used in pulse power needed by electric spark fine machining.
当今脉宽调制技术在电火花微细加工所使用的脉冲电源中得到广泛应用。
The high-frequency and high-voltage pulse power source is the core part of the dielectric barrier discharge.
高频高压脉冲电源是介质阻挡放电的核心部分。
The EDM(electron discharge machining) dressing pulse power was developed based on the requirement of EDM dressing.
根据电火花修整的需要，研制了电火花修整脉冲电源。
We have designed a kind of ion source pulse power and it is used in measure of inelastic spectrum and capture spectrum.
设计了用于非弹性散射谱和俘获谱测量的时间、幅度可调离子源脉冲电源。
Pulse power generator, controlled by an embedded MCU, can produce high voltage or low voltage discharge pulse waveform.
电火花脉冲电源由单片机控制，用于产生高压放电脉冲、低压放电脉冲、间隙状态检测等功能。
Nickel is electrochemical micromachininged using nanosecond pulse power, millisecond pulse power and direct current power.
利用纳秒级脉冲电源、毫微秒级脉冲电源和直流电源，进行了电解加工试验。
The way of realizing micro energy pulse power source is analyzed. A micro energy pulse power source used by micro-EDM is developed.
分析了微能脉冲电源的实现途径，设计开发出了满足微细电火花加工用的微能脉冲电源。
To meet with the requirement of PECF finishing, pulse power source with high frequency, narrow pulse width and high current is designed.
为了满足螺旋锥齿轮等大型零件的脉冲电化学光整加工的要求，设计了高频、窄脉宽、大电流的脉冲电源。
Pulse power with fast rise time technology was applied in many fields such as nuclear physics, electron beam, accelerator, laser, HPM etc.
高功率快脉冲技术在核物理技术、电子束、加速器、激光、HPM现代科学技术领域都有广泛的应用。
Utilizing this kind of solder, we have assembled laser arrays with single-bar pulse power of 100W and stacks with pulse power of 600W each.
利用这种结构的焊料，我们成功地组装出单条无铝线阵脉冲功率100W的线阵，无铝叠阵脉冲功率为600W。
In this thesis, switchgear test power is supplied by a pulse power, composed of a second order oscillating circuit including a capacitance.
区别于现有的微欧仪，本设计采用由电容组成的二阶振荡电路做脉冲电源对开关进行放电。
Crater depth versus pulse power density, average laser power, pulse repetition frequency and focal distances are built up through experiment.
试验建立起了凹坑深度与脉冲功率密度、激光平均功率、脉冲重复频率和离焦量之间的关系曲线。
On the basis of parameter designed, a prototype of high voltage pulse power supply is developed and some researches and tests have been done.
研制成功了一台用于脉冲中子发生器煤质在线分析仪器的脉冲高压电源样机，并在这台样机上进行了试验研究。
When the method of general pulse power of wire cut EDM is used, magnetic steel has magnetic property inevitably and it is difficult to evacuate.
采用一般的脉冲电源对磁钢进行电火花线切割加工，不可避免地将引起充磁，造成排屑困难。
This paper introduces the design method of a kind of distributed pulse power system for solid-state radar transmitter and sharing-current technique.
介绍了一种固态雷达发射机的分布式脉冲电源系统的设计及均流技术。
This paper introduces the design of high voltage low current pulse power supply with two polarities, which is used in a new type chemical surface disposal.
针对一新型表面处理工艺，设计了一种符合工艺要求、可输出双向不对称脉冲的高压脉冲电源实现电路。
This paper presents a indirect measuring and controlling method of pulse power injection with consideration of the high voltage, strong current of this system.
针对脉冲功率注入系统存在高压、强流的特点，提出其间接测控方法。
A bidirectional pulse power supply is designed, which adopts a two stage structure for process requirements. On this basis, its control system is also designed.
设计了一种采用两级结构来实现工艺要求的双向脉冲电源，在此基础上设计并实现了电源的控制系统。
A bidirectional pulse power supply is designed, which adopts a two stage structure for process requirements. On this basis, its control system is also designed.
设计了一种采用两级结构来实现工艺要求的双向脉冲电源，在此基础上设计并实现了电源的控制系统。
应用推荐