The system is composed of industrial PC, DMC300 motion controller, discharge status checking card, A/D card, I/O card and pulse power.
该系统由工业PC，DMC300运动控制器，放电状态检查卡，A/D 卡，I/O 卡和脉冲电源组成。
Because a longer time for the radar pulse to return would imply a greater distance, the Controller would then make adjustments based on an incorrectly estimated position.
所返回的雷达脉冲时间较长就意味着更远的距离，Controller随后将根据不正确的估计位置作出调整。
In this paper, I focus on the design of external controller and internal passive pulse generator of external DBS on the basis of previous.
本文在前人的基础上，重点完成了外置式DBS体外控制器及内置无源脉冲发生器的设计。
The DSP-based excitation controller adopts many advanced technologies, such as alternating current sampling, digital pulse and FFT etc.
文中提出的这种基于DSP的励磁控制器采用了许多先进技术，如交流采样、数字脉冲、FFT等。
The pulse is directly read out by utilizing PLC high-speed counting module, the function of the locating controller can be achieved by program, thus the locating controller are saved.
利用PLC高速计数模块直接将外部编码器发出的脉冲读入，在PLC内部编程，通过程序控制完全能取代位置控制器的所有功能，从而省出位置控制器这一环节。
Responsible for the acquisition of external signals, as people's eyes, when a moving object into its work range, it will give the main controller a pulse signal.
负责采集外部信号，如同人们的眼睛，当有移动的物体进入它的工作范围时，它就给主控制器一个脉冲信号。
It will introduce us a new SAW process by adopting DC pulse current. They design and develop pulse current controller as core of single plate machine.
提出了一种采用直流脉冲电流的埋弧焊工艺，研制开发了以单片机为核心的脉冲电流控制器。
A pulse width modulation controller comprises a disabling unit, a level sensor and an over current protector.
脉冲宽度调制控制器，包括一个禁用单位，水平传感器和过电流保护。
This controller integrates pulse width modulation(PWM) and pulse density modulation(PDM) together, and can easily change between the two modulations.
该设计集成了脉冲宽度调制（PWM）和脉冲密度调制（PDM）两种调制方式，并可以在两者间切换。
The COM of IBM-PC applications for the counter of Opt-encoder pulse and the controller of AC -Servo are study in this paper.
探讨了PC的串行接口用于光电编码器的脉冲计数和伺服电机控制两种非通信功能的应用。
The high voltage endurance test device for switch tube is composed of high voltage pulse generator, high voltage breakdown detector, trigger, auto-controller and DC/AC converter.
开关管冲击耐压装置由高压脉冲产生器、击穿检测器、触发器，及自动控制器、DC/AC变换器等构成。
The single phase H-bridge inverter can generate common-mode voltage due to the sine pulse width modulation(SPWM)and vector controller.
采用脉宽调制和矢量控制的单相H桥逆变器会产生共模电压，后者会对逆变器、电机及其相关设备产生危害。
A pulse vacuum sterilization controller based on AT89C55 is designed, according to the requirements and the work characteristics of the medical treatment.
根据医疗行业对高温灭菌的使用要求和工作特点，研制了基于AT 89 C55单片机的脉动真空灭菌器。
In the paper, engine electronic controller(EEC) which is fit for distributed system is designed from the way of hardware and software, such as regular pulse generator.
从软、硬件角度设计了适用于分布式系统的发动机电子控制器，如周期信号发生器；
The controller controls the timing of the pulses output by the pulse generator such that the period of each pulse relates to a predetermined decay amount.
控制器控制脉冲发生器所输出的脉冲的定时，以使得每个脉冲的周期与预定衰减量相关。
Controller: Pulse Width Modulation electronic speed control for highest efficiency.
控制器：最高效率脉宽调制电子调速器。
With single polar SPWM(Sine Pulse Width Modulation), the whole solution of hardware and software is presented based on the resource of the DSP controller chip.
该系统采用单极性调制的SPWM方式，根据DSP芯片的各类资源给出了一套具体的数字化实施方案。
The adjustor consists of gears and worm-gear reducer, and the automatic controller circuit consists of pulse period discriminator, forward switch, backward switch and protector circuit.
调节器由齿轮和蜗轮蜗杆减速器组成；自动控制电路由脉冲周期鉴别、正向开关、反向开关及保护电路组成。
An FIR controller is designed directly to approximate the inverse plant dynamics defined by its im-pulse response in internal model control (IMC) system.
根据内模控制器是被控对象逆动态逼近的原理，由被控对象的脉冲响应来设计FIR型控制器。
The key design scheme and the method to carry out the pulse-jet cleaning controller based on MCU were presented in the paper. The main software flow charts were also introduced.
给出了基于单片机的脉冲反吹控制仪核心电路设计方案与实现方法，并介绍了系统主要软件流程。
The time of high level and the cycle for input pulse was measured with micro-controller to calculate duty cycles.
单片机通过测量输入脉冲的高电平时间及周期而实现占空比测量。
The time of high level and the cycle for input pulse was measured with micro-controller to calculate duty cycles.
单片机通过测量输入脉冲的高电平时间及周期而实现占空比测量。
应用推荐