This displays icons of each running program and allows you to switch among them.
这会显示每个运行程序的图标，你可以在其中进行切换。
For instance, the -f switch commonly used to tell a program to read a configuration file complicates the configuration because the file may override or supplement options given on the command line.
例如，- f开关通常用于告诉程序读取一个配置文件，这将因为该文件可能覆盖或者补充命令行上给出的选项而使处理变复杂。
To switch between modes, an additional check is required in each pass of the main program loop.
要在模式间进行切换，需要对主程序循环的每次循环执行额外的检查。
Note that changing the JNDI bindings while the program is running will not dynamically switch the program between queues and topics.
注意，如果在程序运行时更改JNDI绑定，则不能在队列和主题之间动态切换程序。
Right click the program icon in system tray to switch the VPN connection on or off.
右键点击系统托盘里的程序图标可以开关VPN连接。
You can switch back and forth between data and code sections, but when the program is assembled it will bring all of each section together into one unit.
您可以在数据部分和代码部分之间自由切换，但当程序被汇编时，会将所有部分汇编到一起，组成一个单元。
Read your neighbor's newspaper, switch seats on the train, or watch a new television program.
读读你邻居的报纸，火车上换个座位，或者看看新的电视节目。
If you switch to the console, you'll see that the program runs and exits without any errors, but it doesn't produce any output.
如果切换到此控制台，您将看到此程序正常运行和退出，但它不会产生任何输出。
The user ID that is issuing the binary deploy is not defined to the RACF program control the _login function to switch users failed.
发出二进制部署的用户ID在RACF程序控制中没有定义。用于切换用户的_ login函数调用失败。
Now switch to NUnit and note that the treeview's nodes are all grey, indicating that the test cases have not yet been run for the program you've just updated.
现在再切换到NUnit，注意到Treeview的所有节点均为灰色，这表明你更新后的程序还没有运行。
In my example, the first half of the program is simply a switch to allow manual selection of the backend to use from the command-line.
在我的示例中，该程序的上半部分完全是实现一个switch，允许从命令行手工选择要使用的后端。
And when it does perform a thread switch, it tends to do it in the same place whenever you run the program.
并且当它确实执行了线程切换时，每次运行程序时它往往都在同一个位置进行切换。
When a context switch occurs in cases such as virtual processor conferring its cycles to another virtual processor, it will be required to save the entire program visible processor state.
在出现上下文切换的情况下(如虚拟处理器将其周期交换给另一个虚拟处理器的时候)，必须保存整个程序的可见处理器状态。
They invented the stored program control switch in the 1970s, as a move toward cost reduction and reliability.
1970年代他们发明了程控交换机，保证了可靠性，降低了成本。
If you're trying to check your emails less often, make it difficult to open your email program (or switch off your Internet connection altogether).
如果你努力去减少查收邮件的次数，那么让邮件程序的打开变得不那么容易(或者完全切断网络连接)。
Positioning the switch in this mode enables the automatic control of the machines to use information entered in the form of blocks without interfering with the basic program.
开关定位在此模式，可以利用与基本程序没有冲突的程序段形式进行信息输入，实现机床的自动控制。
For example, a program that needs a single root privilege may get started as root (say, by being setuid root) and then switch to running as a less-privileged user.
例如，需要个别的root特权的程序可能以root身份启动(比如说，通过成为setuid root)然后切换到以较少特权用户身份运行。
Your task is to tell us how many times the central system will have to switch between search engines, assuming that we program it optimally.
你的任务是告诉我们，假设我们编写最优的程序那么中心系统将必须切换搜索引擎多少次。
The component of system, locale disposal of detect switch and design of system program have been described in details.
详细阐述了系统的组成，检测开关的现场布置以及系统程序的设计。
According to test flow, the host program and its partial code are given, and according to the hardware structure of switch matrix, the firmware of each part is also given.
根据测试流程，给出了主机控制程序设计及部分实现代码，并针对开关矩阵硬件构成，分别给出了各个组成部分的固件程序代码。
Through analyzing the power flow in a switch network, a calculation method and formula and its program block diagram of conductance ratio of every switch are put forward in this paper.
通过对开关网络的潮流分析，得出实际运行条件下计算开关网络中各开关电导比的公式和求解方法，并给出了程序框图。
A scheme for designing the three-position switch with both analog and digital devices is presented with specific diagram and program code.
介绍了一种利用模拟可编程器件和数字可编程器件设计三工位开关控制器的方案，并给出了具体的电路图和程序代码。
Ruifeng hardware switch socket comprehensive quality control: from design to use, each program are strict quality control, so that the quality is completely reliable.
瑞丰五金开关插座全面品管：产品从设计到使用，每一程序均严格品管，使品质完全可靠。
Virtual resources are used in test program coding in ATLAS and after compiling, the program will control practical instruments and switch to complete test task.
虚拟资源将被用于ATLAS语言编写的测试程序，并在编译之后，根据虚实映射结果控制具体的仪器和开关完成测试任务。
Operation: Once get power supply, loads and thermal resistors connected, press the power switch of temperature controller, and then it will start temperature control program automatically.
使用：接好电源、负载及热电阻线后，按下温控器电源开关，温控器即可自动投入定温控制运行。
The main control module has two operational modes of re- mote control and program control, and uses remote control command to switch operational mode.
主控模块采用遥控与程控两种工作模式，并通过遥控指令实现模式切换。
You can switch between worker threads and worker processes by changing a single word in your program.
你可以通过改变程序中的一个文字工作者线程和工作进程之间的切换。
You can switch between worker threads and worker processes by changing a single word in your program.
你可以通过改变程序中的一个文字工作者线程和工作进程之间的切换。
应用推荐