The driving force depends on the pressure distribution.
该推动力的大小由压力分布决定。
The pressure distribution was simulated with a approximate method.
采用近似方法模拟径向滑动轴承压力场分布。
Tests of pressure distribution in Squeeze film damper are performed.
对挤压油膜压力分布进行了测试。
The features of pressure distribution on overline bridge are discussed.
文中还分析了跨线天桥上压力分布的基本特征。
An iteration method is used for computing the transonic pressure distribution on a flexible wing.
本文采用迭代求解的方法计算弹性机翼的跨音速压强分布。
The model can simulate the velocity and pressure distribution of molecular in the pumping channel.
这个模型可以模拟在分子泵抽气通道内的气体分子速度与压力的分布。
The fluid load in pipeline is calculated, that is calculating the pressure distribution of pipeline.
计算管线内部流体荷载，也就是管系的压力分布计算。
According to the changes of deviation Angle calculated the pressure distribution of directional well.
对定向井井筒压力分布，计算时根据井斜角的变化采取分段计算的方法。
In this paper, pressure distribution of gaseous slip flow in parallel plates microchannel was studied.
对平行平板微型槽中气体滑移流动的压强分布特性进行了研究。
Computing pressure distribution is the base of analyzing and calculating various performances of bearing.
求解压力分布是对轴承各项性能进行分析计算的基础。
Crown Drop of a Needle roller decides the pressure distribution between roller and raceway, capability and life.
轴承滚针的凸度设计，决定了滚动体与滚道间的接触压力分布，影响其性能和寿命。
This method is direct, in that it gives the surface-pressure distribution and shock shape for a prescribed body.
方法是直接的，即由给定物体形状可求出表面压力分布和激波形状。
The fluid streamlines and pressure distribution and LZVV phenomena for the hydrocyclone are given in this paper.
计算得到了水力旋流器内的流线图、等压线以及零速包络面。
Aim To study the rules governing pressure distribution of traveling charge under the condition of Lagrange hypothesis.
目的研究拉格朗日假设条件下随行装药的膛内压力分布规律。
Firstly, the pressure distribution of gas solid flow along the circulating route is analyzed and experimentally studied.
分析气固两相流在循环路径中的压力分布，并通过试验对其进行了研究。
Initially this region will be blank, note that the temperature distribution behaves qualitatively like the pressure distribution.
最初这一地区将会是空白，请注意温度分布的所作所为定性一样，压力分布。
The design process of the piezoelectric force sensor in the insole plantar pressure distribution measurement system was introduced.
摘要介绍了鞋垫式足底压力分布测量系统中压电陶瓷力传感器的设计过程。
The design process of the piezoelectric force sensor in the insole plantar pressure distribution measurement system was introduced.
介绍了鞋垫式足底压力分布测量系统中压电陶瓷力传感器的设计过程。
This paper analyzes the pressure distribution around the stationary cylindrical Model based on the experiment using the theory of flow.
本文应用绕流理论对圆柱形煤锭模型纵向绕流的受力在实验的基础上进行了分析。
The simulation and analysis of the pressure distribution in head runner of double plex tread extruder were made with ANSYS FEA software.
采用ANSYS有限元分析软件对胎面双复合挤出机头流道内部的压力场进行模拟和分析。
Although it is very small in size, some developments in the test section of pressure distribution on airfoil surface have been attempted.
尽管该风洞的尺寸很小，我们仍对翼型表面压力分布试验段的研制工作进行了大胆的尝试。
For airflow around a circular cylinder, the pressure distribution is studied numerically, and the response of the pressure sensor is foretold.
利用数值模型计算了空气流过圆柱体的压力分布，并预言光子晶体压力传感器的响应。
The computation shows that the observed pressure distribution can be well reproduced by the elastic theory with a spatial varying bulk modulus.
计算表明用考虑了体弹模量随空间变化的弹性理论能很好地再现出观测到的压力分布。
Predicted pressure distribution and lift coefficient are in agreement with numerical results and experimental data available in the literature.
压强分布和升力系数的计算值与现存文献的数值结果和实验数据是一致的。
Technique of in flight measurement of pressure distribution on a subsonic transport aircraft is introduced. Some flight test results are presented.
简要地介绍了亚音速飞机压力分布测量的飞行试验技术，并给出了部分试验结果。
Effect of parameters on lubrication film shape and pressure distribution was analyzed for the typical working conditions of automotive wheel bearings.
针对轿车轮毂轴承的典型应用工况条件，分析工况参数对油膜压力分布和油膜形状的影响。
A numerical method is presented for prediction of propeller performance and pressure distribution on blade surface according to lifting surface theory.
本文提供了一种根据升力面理论计算螺旋桨桨叶表面压力分布和螺旋桨性能的数值方法。
The method is applied to free surface sluice gate flow over spillway and computed pressure distribution agrees satisfactorily with experimental results.
用这种方式可以减少计算的工作量，算出的溢流面压力分布资料和试验结果符合较好。
The flame velocity of flammable gas deflagration in a large closed vessel has an accelerating process, and the pressure distribution is not homogeneous.
大型密闭容器内可燃气体爆燃的火焰速度存在着一个加速过程，压力也不是均匀分布的。
The predicted results of the wall pressure distribution, axial velocity profiles at the outlet and the spray Angle agreed well with the experimental datum.
计算得到的壁面压力分布、出口处液膜内轴向速度分布以及雾角大小都与实验结果吻合的很好。
应用推荐