Automatic calculation and adjustment of press force.
折弯出力吨数由电脑计算自动调整工作压力。
The calculation methods of deformation and contact press force of sealing rings are derived.
推导了组合型密封环的压缩变形量及接触压力的计算公式。
The influences of friction coefficient between tube and mandrels and the press force on the end of tube for thickness chang...
通过数值模拟得到管壁的最大减薄和增厚部位，并讨论了芯轴的摩擦系数和钢管末端的压力对管壁厚度变化的影响。
A scandal that has licked around the feet of politicians and scorched the press rather more (see Bagehot) has burned Britain's biggest police force badly.
一起牵涉到政客还把媒体惹得更焦头烂额的丑闻大大激怒了英国最大的警察队伍。
Five white, with both hands thumb to press knead 30 times, thumbs down output, but not excessive force.
五点四白，用双手拇指端先按后揉30次，拇指指腹向下出力，但不宜用力过大。
Factory workers then use a loud press machine to strike the mold with 550 tons of force — three times — to create the coveted round symbols of victory.
接着，工人们使用冲压机用来冲压模具，其力量高达550吨——且需冲压三次——就制造出了大家梦寐以求的、圆形的、成功的象征——奥运奖牌。
The pneumatic muscle is ideal when used for the actuation of a small press, because a high force is exerted via a short stroke.
气动肌腱具有在短行程中产生高输出力的特点，所以，是一种小型压力机和冲压机的理想驱动器。
The experiment results show this method is applicable to identification of fingerprint image with a little distortion owing to the finger press part and force different.
实验表明，这种识别方法特别适于由于手指按压部位不同和用力大小不同而产生少许变形的指纹图像的识别。
The construction of static pressure is to press the pile into the soil with reaction force provided by the static pile driver weight, and balance weight on the rack.
静压法施工是通过静力压桩机的压桩机构以压桩机自重和机架上的配重提供反力而将桩压入土中的沉桩工艺。
Usually the compressive force is in the form of hammer blows using a power hammer or a press, as shown in Fig. 4.1.
通常压力都是以由如图4.1所示的动力锤或压力机提供的锤击形式出现。
Press conference is a special activity type. This paper tries to explain and verify the interpreting force of activity type theory toward Chinese text.
记者招待会是一特殊会话活动类型，本文试用会话活动类型理论解析并验证该理论对汉语语料的阐释力。
A crack press was compared with hydraulic force increasing press and the schematics of them were introduced, a force increasing ratio of the orthogonal force amplifier was calculated.
本文将曲柄连杆压力机与液压增力压力机的特点作比较，并介绍液压增力压力机和正交增力机构的工作原理，进行正交增力机构增力系数的计算。
It can obviously decrease the press of the system in the situation of the output force and the diameter of the hydraulic cylinder is limited.
在输出力及液压缸直径一定的条件下，能显著降低系统的压力。
The press machine is selected through the technology force calculation, and the shut height as well as power is checked.
通过对各工艺力的计算初步选定了压力机并进行了闭合高度校核和功率校核。
The machine for the Four-column press, using optimized hydraulic drive program, with a strong driving force, accurate positioning and a perfect combination of actions.
本机为四柱式压力机，采用优化的液压传动方案，具有强大的动力，精确的定位和完美的动作组合。
The causes of vibration on high speed press consist mainly in the inertial force of crank slide mechanism and the working force of the press.
高速压机的振动原因，主要是曲柄滑块机构的惯性力和压制工作时的加工力。
In order to enlarge the force of middle beam, the double-frame press has been designed.
为了达到大的中间板上作用力，常采用双框架压力机床身结构。
The influencing factors of the return force of 165MN oil pump direct-drive free forging press have been analysed and the design principle of the press's return force given.
分析了165MN自由锻造油压机回程力的影响因素，给出了压机回程力的设计依据。
In order to utilize the force of the press efficiently, a progressive device for CGF crankshaft forging has been recommended.
为了有效地利用压机的压力，作者推荐了一种改进的装置。
When the method is used, the area of the cutter blade pressed by the press block is relatively large, so the cutter is prevented from being damaged due to the certain impact force.
采用这样的方式，刀片被压块压住的面积比较大，不会因为受到某些力冲击的时候，使刀具报废。
With the increase of the beam rigidity, the length of the press area and the axes tension force of the beam near the gate-hole increase.
随着梁刚度增加，梁端受压区段长度增加，门洞处梁轴向拉力加大；
A new force sensing system of 6-dof parallel robot was proposed by integrating 6 pull-press sensors on the 6 linkages.
通过在6 -DOF(6自由度)并联机器人各个杆件上集成拉、压力传感器，组成了新型力感觉系统。
The natural frequency of the press is far higher than the frequency of inertial force.
压机固有频率比惯性力频率高得多。
Press forgings. Press forgings use a slow squeezing action of a press, to transfer a great amount of compressive force to the workpiece.
压锻通过压力机缓慢的挤压动作将巨大的压力传递给工件。
The analysis results supply a theoretic foundation and reference for forecasting rolling force online and working out the regulations of slab siding press.
分析结果为板坯侧压规程的制定和轧制力的在线预报提供了理论依据。
The analysis results supply a theoretic foundation and reference for forecasting rolling force online and working out the regulations of slab siding press.
分析结果为板坯侧压规程的制定和轧制力的在线预报提供了理论依据。
应用推荐