Aiming at the shortage of traditional method of measuring power frequency parameters of overhead transmission lines, measurement of power frequency parameters by non power frequency is put forward.
为了解决输电线路在高感应信号下，准确方便地测量线路的工频参数，针对架空输电线路工频参数传统测量方法的不足，提出了异频法测量线路工频参数。
The influence of the parameters such as surface treatment state, laser output power, welding speed, protective atmosphere, and pulse frequency on the welding quality was studied.
研究了试件表面处理状态、保护气体、激光输出功率、焊接速度、激光脉冲频率等工艺参数对焊接质量的影响规律。
As for the numerical simulation by traditional power system component models and parameters, the obtained dynamic frequency curves evidently diverge from measured ones.
采用常规的电力系统元件模型和参数进行数值仿真所得的频率变化曲线与实测曲线偏差较大。
We can monitor many parameters and characteristics by measuring TEN, such as surge frequency, spectrum width, threshold current, mode jump and stability of output light power.
通过对激光的电噪声的测量可以监测激光器的诸多参数和特性，如弛豫频率，谱线宽度，阈值电流，模式跳变及输出光功率是否稳定等。
The electric parameters such as inductor current, power frequency and energy consumption etc.
计算出铝合金扁锭的感应器电流、电源频率、功率和能耗等电参数；
Three features parameters derived from the instantaneous amplitude, instantaneous phase, instantaneous frequency and power spectrum of analogue modulated signals are presented in this article.
首先介绍从信号幅度、相位、频率及功率谱等特性中提取的三种特征参数，应用这三种参数采用人工神经网络对模拟调制信号进行了识别。
Electric power system frequency is an important indicator of power quality and is one of the most important parameters of power system operation.
电力系统频率是电能质量的重要指标之一，也是电力系统运行最重要的参数之一。
Some parameters affecting the frequency and magnitude of power supply, such as supply voltage, duty of control sigal. the R and C of oscillation circuit are discussed.
对影响放电电压大小及频率的电源参数进行了讨论，如供电电压、控制信号占空比、振荡电路的R和C等。
The results show that the rational combination of welding parameters such as the laser power density, the welding speed, the pulse frequency and pulse width influence the quality of the weld beam.
焊接过程中合适的保护气体及其送气方式也是十分必要的。大量试验表明，激光功率密度、焊接速度、脉冲宽度和脉冲频率四个参数的合理组合是实现不锈钢薄板焊接的关键因素。
Noise value, noise power, noise voltage, vibration power and amplitude vibration were measured under different cutting parameters of technology and frequency spectrum analysis was also made.
在不同的锯切工艺参数和锯片结构下，测量了噪声值、噪声功率、噪声电压、振动功率和振动幅值，并对其进行频谱分析。
The Wigner Ville time frequency analysis in conjunction with properly selected OFDM parameters is applied to evaluate the signal dynamic range performance over the low voltage power line network.
为了研究OFDM信号在低压电力线上的传输情况，运用基于维格纳分布的时频分析方法对电力线上的信号进行分析。
The traditional measure method of the power withstand test is to use the voltage meter, ammeter, power analyzer, frequency analyzer etc to measure the waveform and parameters of the power signals.
传统的工频耐压试验是通过电压表，电流表，功率分析仪，频谱分析仪等等来分别测量波形及其各个参数的。
As power is the critical equipment of micro oxidation technology, its parameters, such as voltage, current density, pulse frequency, have a very important impact on the quality of the film.
作为实现微弧氧化技术关键的电源设备，其电参数，如电压、电流密度、脉冲频率、脉冲占空比等参数对膜层的质量有着极其重要的影响。
The impacts of the variations of the active power vacancy and other relevant parameters on the frequency dynamic process were pointed out.
指出有功缺额等相关参数的变化对系统频率动态过程的影响。
In high-frequency switching power supply, influence on switching power supply by the more parasitic transformer parameters is increasing.
大功率通信高频开关电源的噪声干扰中除了有谐波的传导干扰外，还存在电磁的辐射干扰问题。
In high-frequency switching power supply, influence on switching power supply by the more parasitic transformer parameters is increasing.
大功率通信高频开关电源的噪声干扰中除了有谐波的传导干扰外，还存在电磁的辐射干扰问题。
应用推荐