Direct control of torque over the motor speed range is provided by the drive, which helps the motor and drive generate torque levels high enough to cycle the press back to ready position.
直接控制扭矩而不是电机转速范围，可以使得电机和变频器产生足够高的扭矩使得压机可以回复到原来的位置。
Acquisitions and strategic partnerships, in conjunction with increased research and development investments, have allowed the leading motor manufacturers to better position themselves for the future.
在加大研发投入的同时，通过收购和战略合作，让领先的电机制造商能够更好地定位自己的未来。
Most often this is in some kind of valve, but it might also be a belt of motor speed, louver position, and so on.
最常见的是由某种阀来完成，但这也可能是一条皮带，或者是马达速度、口径位置等等。
The label position control is used to enter a delay distance of travel for the Product before the label drive motor begins to move.
机器会对标签位置的进行控制，以使产品在标签驱动电机开始运行前在传输带上保持一定的滞后距离。
According to the problem of position of DC torque motor, an new fuzzy control way was put forward.
针对小功率直流力矩电动机的定位控制问题，提出了一种新的模糊控制策略。
The closed loop control of the motor position and velocity are realized using the microcomputer.
采用计算机实现了变磁阻电机的位置和速度闭环控制。
The design of the single chip system, sample box thermostat circuit, sample position detecting circuit and step motor control circuit are discussed.
着重讨论了单片机系统、样品箱恒温电路、样品位置检测电路和步进电机控制电路的设计。
The test results indicate that the system can realize comparatively precise position control of the motor.
试验表明，该方法能实现对电机转子启动位置的精确控制。
Depending on the switch position and the direction of current to the armature, the appropriate motor will either revolve clock-wise of counterclockwise to produce the desired seat movement.
根据开关的位置与流入电枢时电流的方向，电动机开始顺时针或逆时针旋转从而使座椅根据需要进行调整。
When the arm runs to the upper and lower two limit position, respectively press the lower limit switch, cut off the main control circuit, variable amplitude motor parking, to limit the role.
当臂杆运行到上下两个极限位置时，分别压下限位开关，切断主控电路，变幅电机停车，达到限位的作用。
At startup, there is no back-EMF due to the stationary motor, and the motor position cannot be detected in sensorless mode.
在启动时，没有反电动势，在无传感器模式下电机的位置不能检测到。
A novel method that USES the harmonic back EMF signal to extract the rotor position is put forward, and a new position sensor merged into an organic whole with the motor is designed.
提出了一种利用谐波反电势信号实现电机转子位置检测的新方法，设计了与电机一体化的新型位置传感器。
The position and velocity were controlled by servo and the DC motor respectively.
输出控制量最终通过舵机和直流电机分别对小车的位置和速度进行控制。
There are position sensor windings in addition to armature windings in the motor.
这种电机内部除了电枢绕组以外，还带有位置传感线圈。
In DC motor, the locality of axis of armature MMF was determined by the brush position, here the brush possessed a function of clamping.
直流电动机中电枢磁动势的轴线位置是由电刷位置决定的，电刷具有箝位的功能。
Using an optical incremental encoder and hardware interface, the position of the motor rotor between the two teeth of the motor stator is measured.
采用高分辨率的增量式光电编码器和相应的硬件接口电路，实现了变磁阻电机转子在定子两个齿之间位移的检测。
For example, a stepper motor requires a series of digital pulses as an input to control the motor position and speed.
举例来说，步进电机需要输入一系列数字脉冲信号来控制电机的位置和速度。
In order to satisfy this requirement, the complex signal lines are usually used to detect the speed and position of each motor and to command the desired speed and position.
为了满足这个要求，检测每个电机的速度和位置数据以及传送指令都需要大量复杂的数据信号线。
The paper mainly focus on the experimental research on pneumatic on-off valve motor position servo control system with PCM control method and self-adjusting PID algorithm.
文章主要研究的内容为利用PCM控制技术，采用自适应PID控制算法，对开关阀式气动马达位置伺服系统进行实验研究。
Mount valve against the motor with the ports in corresponding position.
山阀对电机与港口相应的位置。
The system with CPU drives the DC brushless motor, and the encoder indicates the motor position outputting the sine and cosine signal.
系统采用CPU驱动直流无刷电机转动，编码器输出的正余弦信号指示电机的位置。
Position detection of rotor in hybrid stepping motor servo system can use traditional outside position sensor or sensorless scheme based on theoretical algorism, but there are many problems produced.
混合式步进电动机伺服系统转子的位置检测，可以用传统的外配位置传感器或基于理论算法的无位置传感器方案，但是存在许多问题。
Describes a novel method of detecting for rotor flux position of the brushless DC motor (BLDCM).
介绍了无刷直流电机无位置传感器转子位置检测的一种新方法。
Then position detection technology, hardware and software system design is discussed. The initial position of the motor is a main problem for control of PMLSM.
然后针对永磁直线同步电机控制系统的主要难点，分为位置检测技术，硬件系统设计和软件系统设计三个方面对控制系统进行分析。
The exact rotor position is required while a permanent magnet brushless servo motor (PMBSM) is under commutation and control. Howere, position sensors have some fatal defects.
永磁无刷伺服电机的换相和控制都需要准确的转子位置信息，然而位置传感器有其难以克服的缺点。
This paper describes a novel method of detecting for rotor flux position of the brushless DC motor (BLDCM).
介绍了无刷直流电机无位置传感器转子位置检测的一种新方法。
This paper describes a novel method of detecting for rotor flux position of the brushless DC motor (BLDCM).
介绍了无刷直流电机无位置传感器转子位置检测的一种新方法。
应用推荐