And the normal engagement angle of approaching double-point tooth area is deduced. The special dressing method of shaving cutter has been adopted.
推导了进入双点啮合区的法面啮合角公式，采取了独特的剃齿刀修形方式，从设计和修形上下功夫杜绝剃齿中凹的产生。
At that point in my life, I still believed in the magical trifecta—Santa Claus, the Easter Bunny, and the Tooth Fairy.
在我的生命中，对于此，我仍然相信不可思议的三连胜式——圣诞老人、复活节小兔和换齿仙子。
These formulae are suitable for any contacting point of tooth surface meshing.
这些公式适用于齿面啮合的任何接触点。
When interference of tooth shape occurs, the coordinate value of drive engagement point would be rectified by the computer on line until the interference disappears.
在齿形干涉出现时，对主动件相应的啮合接触点坐标值由计算机自动进行增值修正计算，直到干涉消失。
In small tooth difference of inner meshed transmission, there were a few pairs of tooth faces which were apart from each other for a small gap beside the contact point generated by two meshed teeth.
在少齿差内啮合传动中，存在多对接近啮合的小间隙齿面于理论啮合点左右，轮齿受力产生的微小变形使得某些对齿面相互接触进入啮合状态。
But before they reach that point of open and avowed defeat, they will fight tooth and nail to maintain the standard of excellence to which they have become accustomed.
但是在到达他们公开自认失败的临界点前，他们会尽量咬咬牙维持他们所适应的令人兴奋的生活。
The most dangerous point is at the root of the first engaged tooth of a joint. Generally, the biggest values of stress and strain may exceed the yield limit.
最危险点在接头的第一啮合齿的齿根处，最大应力应变值一般均超过屈服极限。
The common gear tooth profile curve launches after neighborhood higher order step taylor's series, can discover the tooth face meshing point neighborhood gap is 2 step infinitely greats.
一般齿轮齿形曲线在一点邻域的高阶阶戴劳级数展开后，会发现齿面啮合点邻域间隙为2阶无穷小。
This paper proposed a new method that was based on network node and applied to compute tooth contract-point line of engaged gears for different mesh position.
本文提出了一种以网络结点为基础，在齿面上的活动标架里，计算齿轮在不同啮合位置的接触点，以求得接触迹线的新方法。
Deviation measurement of tooth thickness and conical point of straight bevel gear by using steel bail was studied and approached.
对钢球法测量直齿圆锥齿轮齿厚及锥项位置误差检测进行了研究和探讨。
Finally, for an example, a maximum stress point and stress distributions of a synchronous belt tooth have been found out and compared with its elastic linear solution.
最后，通过一个具体算例求出梯形齿同步带一个齿上的最大应力点及应力分布规律并与弹性平面问题的解进行了比较。
The errors of grinding wheel dressed by diamond point cause the race to produce non-circular arc tooth profile errors.
金刚石笔修整砂轮误差使滚道在磨削时产生非圆牙形误差。
The values based on the three stimulation value were adopted for the colour selection and tooth colour matches from nine zone colors with 21 point smoothly transitional calculation.
采用一种基于三刺激值的相对选色方法及2 1点平滑牙色过渡算法的九分法的牙齿颜色匹配；
It pointed out that the design of gear cutter should greatly increase the tooth point arc so as to reduce the stress concentration to increase the force of tooth root.
指出通过计算作出图形，可分析出滚刀齿顶圆弧的设计是否合理。
The equabions on tooth shape of internal gear by means of envelope method is derived and the pressure angle, inflection point, curvature, topcut are analysised in detail.
用包络法导出了内齿轮的齿形方程，对压力角、曲率、拐点、顶切进行了详细分析，并给出了计算公式。
The error sensitivity of contact position of point-contact tooth surfaces with respect to the mounting errors is an important index to evaluate the gearing performance.
点接触齿面的接触点位置对安装误差的敏感性是衡量齿面传动性能的一个重要指标。
Pangolin provide customers with a variety of rotary drilling accessories, including bucket teeth, tooth Block, the center point, to mention inducer.
我公司为广大用户提供各种旋挖配件，包括各种斗齿、截齿、齿座、中心尖、提引器等。
According to point coordinates on the tooth surface calculated theoretically and using FORTRAN, this paper compiles the programs and builds 3d finite element model of the helical gear.
运用FORTRAN语言，并根据理论计算得到齿面点坐标，编制程序，建立斜齿轮三维有限元分析模型。
Some point is very clear, the Sri Lankan to the Buddha's tooth believed that does not move.
有一点很清楚，斯里兰卡人对佛牙坚信不移。
The wench that takes this tooth point mouth benefit has no a way and eat dirt of add a way: "Square small dye go to which?"
拿这个牙尖嘴利的丫头毫无办法，忍气吞声的补充道：“方小染去哪了？”
Results showed that: in the same cutting depth, the force employed on the point-attack pick is bigger than that on the knife tooth;
试验结果表明：相同截深时锥形截齿截割力比扁型截齿截割力大；
Results showed that: in the same cutting depth, the force employed on the point-attack pick is bigger than that on the knife tooth;
试验结果表明：相同截深时锥形截齿截割力比扁型截齿截割力大；
应用推荐