Characteristics of low melting point alloy materials and dies of the alloys are described in the article.
介绍了低熔点合金材料及低熔点合金模具的特点。
The paper developed low-melting-Point alloy cores, through die casting experiment, the cores hole deformed well.
自行研制的低熔点合金型芯，经压铸实验，铸件孔成形完好。
Experimental result by low-melting point alloy on the electromagnetic damming for the melt puddle of twin roll steel strip continuous casting is reported.
报道双辊薄带钢铸轧熔池电磁侧封低熔点合金模拟试验研究结果。
The austenitizing temperature was raised by addition of RE and low melting-point alloy which were the elements of strongly promoting and stabilizing the pearlite.
同时稀土与低熔点合金元素的加入，是强烈促进珠光体的元素，具有稳定珠光体的作用，提高了奥氏体化温度；
Though the analyzing of the upper part of oil box and the designing of the structure of the die, the article discusses the characters and advantage of the low melting point alloy die.
以分析起重机油箱上体工艺特性和设计其低熔点合金拉深模具结构为例，论述了低熔点合金冲压模具的结构特点及优势。
The results indicate that the classical heat transfer mechanism is suitable for the medium wall load and the potential heat of the low-melting-point alloy is useful for high wall load.
结果表明，对于中等壁负荷，传统的传热机制是适宜的，而对于高强壁负荷，把低熔点合金的相变贮、放热机制引进到混合堆的热工学中是有意义的。
To solve the problem of short service life and poor performance of low melting point alloy mould manufactured by arc spray forming, the manufacturing of stainless steel mould has been presented.
为了解决低熔点材料电弧熔射成形模具使用性能差、寿命低等问题，提出电弧熔射成形制作不锈钢模具的方法。
This article introduces the use of low melting point alloy dies in coach manufacture, and discusses its principles and characteristics as well as the making and fitting processes of the sample pieces.
着重介绍低熔点合金模具在客车上的应用情况；详述低熔点合金模具的原理、特点以及样件的制作与装配过程。
This preform is then heated to a temperature just below the melting point of the alloy.
此时，将初步加工的成品加热到一定的温度，这个温度要刚刚低于合金的熔点。
Different base metal alloy has the different melting point and linear coefficient expansion.
不同的基底合金具有不同的熔点及线膨胀系数。
In this paper, enhancing the burning point and improving the corrosion resistance and the mechanical property of magnesium and magnesium alloy with the method of alloying are introduced.
论述了采取合金化的途径，提高镁及其合金的燃点，改善镁及其合金的耐蚀性以及力学性能。
High strength plate also known as high strength plate, low alloy high strength plate, high strength welding plate. It is characterized by high strength and high yield point.
高强板又称高强度板，低合金高强板，高强度焊接板。主要特点是强度大，屈服点高。
The Zn-Al alloy has many advantages, such as good mechanical property, strong antifriction property, processable property, small density, low melting point, affluent raw material, low cost and so on.
高铝锌基合金具有优良的力学性能、耐摩性能、机加工性能、以及密度小、熔点低、原材料来源丰富和成本低等优点。
It was used to sintering high melting point material-cerium-tungsten alloy, and gained good effect.
将此高温效应用于烧结高熔点材料——铈钨合金，获得了很好的效果。
The rheology properties of polymer filled with lower melting point dual component metallic alloy were studied by Hakke rheometer.
利用哈克流变仪对低熔点双组分合金填充聚合物材料体系的流变性进行了研究。
Molybdenum is the rare metal with high melting point, which is often used to prepare alloy steel, refractory steel and stainless steel.
钼是一种宝贵的稀有高熔点金属，是生产合金刚、不锈钢、耐热钢和合金铸铁的重要合金化元素。
The transformation point of BT22 titanium alloy was determined using calculation and continuous heating-up method.
利用计算法和连续升温金相法测定了BT22钛合金相变点。
Adding lead makes the alloy easier to cast because the melting point is reduced and the fluidity is increased.
添加铅使那种合金易于铸造，但合金的熔点有所降低。
In order to prevent the yield-point elongation occurring the manganese equivalence in alloy must exceeds 1.61%, and the threshold value of Martensite volume fraction is 7%.
为了不发生屈服点延伸，合金中的锰当量必须超过1.61%，马氏体体积分数的门槛值为7%。
When deforming near beta transition point, it may lead to the uncertainty of microstructure and properties of TC18 alloy.
在相变点附近变形时容易导致合金组织和性能出现不均匀性。
The photos showed that, instead of using a single alloy of some low-melting-point metal, the element consisted of three types of metal.
照片显示保险丝由三种金属组成，而不是使用某种低熔点金属的单一合金。
The results show that the melting point of brazing alloy is constant when the content of boron and silicon is reduced and the right amount of copper is added in.
试验结果表明，在降低镍基钎料中硼、硅元素的同时加入适量的铜可以使钎料的熔点基本不变。
The paper includes two parts, and the focal point of this part is the Fe-Cr-Al, Fe-Cr-Si andnoncrystalline Fe alloy.
全文共分两部分，下半部分主要介绍在铁铬铝系合金、铁铬硅基系合金和非晶态铁基系合金特性研究方面的进步。
Zinc-alloy has low melting point and is easy to spray forming which can be sprayed directly on the production surface to fabricate a mould with high precision by arc spraying.
锌合金熔点低、喷涂成形性能好，可以直接在原型表面进行电弧喷涂快速制造模具，提高模具的制造精度。
Zinc-alloy has low melting point and is easy to spray forming which can be sprayed directly on the production surface to fabricate a mould with high precision by arc spraying.
锌合金熔点低、喷涂成形性能好，可以直接在原型表面进行电弧喷涂快速制造模具，提高模具的制造精度。
应用推荐