Braided gabion: in addition to the lateral plate cover, end plate and the bottom plate are inseparable.
格宾网箱的编织结构:在除盖的外侧板,端板和底板不行支解。
For example one patient gave me a two-plate stove to cover my costs so I could do the work.
比如有一次,一个病人给了我一个双板煤气炉还支付运费,这样我也能继续工作了。
When hand-printing, cover the plate with newsprint so that the baren slides smoothly.
当手工印刷,覆盖薄层板上,以新闻纸,这样的巴伦滑动顺畅。
The damage factors are mostly poor equipment, low or high pressure bag, the bag from the top blowing in the porous plate or dust cover, eventually friction damage.
破损因素是大都为设备不良,袋口小或压差过高,使滤袋脱离多孔板顶在喷吹管或除尘器盖板上,终究磨擦破损。
To plate metal is to cover it with a thin layer of gold, or silver, etc.
电镀金属就是把金属薄薄地覆盖上一层金或银等。
Cover the dough with a plate and leave it for half an hour before it is used.
用板材盖面团和留下它在半小时在它被使用之前。
Caution: Do not loosen nuts on cover plate - This will result in loss of pre-charge.
警告:不要松开盖板上的螺母-这样做可能会导致预充气压力的损失。
Thee patient lifted the cover on her dinner to discover her chicken curry and rice was squashed on the same plate as a summer fruits crumble.
当这位就医患者揭开餐盒,准备吃晚饭时,发现她的鸡肉咖喱饭和水果糖酥塔居然是放在一个盘子里的。 。
Bladder is attached to tank at both ends. To remove bladder from tank remove all bolts from cover plate and take off plate.
内胆附在膨胀罐的两侧。要从膨胀罐上拆卸内胆,就要先从盖板上拆卸所有螺栓并将盖板拿开。
Automobile clutch consists of driven plate assembly and cover assembly. The rotation intensity is an important quality evaluation index of clutch.
汽车离合器由压盖总成和从动盘总成组成,其旋转强度是重要的质量评价指标。
The exterior insulation plate and the upper observation cover adopt stainless steel, to improve corrosion resistance and extend service life.
外保温板和上观测盖采用不锈钢板制作,提高抗腐蚀能力,延长设备使用寿命。
Turn the hollow bolt so that it is fixed on the bake cover or the flange plate.
安装后必须旋出空心螺栓锁紧在电机后端盖或法兰盘上。
The net cover fold down, pull in place and with the front plate, side plate and plate twisted together.
将网盖向下折,拉到位并与前板、侧板及隔板绞合在一起。
Also it is possible that the fatigue strength is greater than that of conventional cover plates perhaps because of the thinness of the slider plate.
同样,该疲劳强度可能比传统盖板的要大,可能是因为滑板的薄性。
If you open the cover plate of your cell phone you'll see a rectangular LCD on its backside.
把手机的盖板打开来,背面就是一整片长方形的液晶萤幕。
Motorcycle's crankcase cover plate is its engine's major component, which would vibrate to radiate noise under the force of the crankcase when the motorcycle'sengine operates.
摩托车的曲轴箱盖是发动机的主要构件,在摩托车发动机运转时,会受到曲轴作用的激振力而发生振动向外辐射噪声。
Otherwise, the bracket should be placed in the bottom of the main horizontal cover plate near the main beam two points to high.
否则应把支架垫在主梁的下水平盖板靠近主梁两点变高处。
The SB series stuffing box cover combine the functions of wear plate and stuffing box into a one-piece replacement unit. One bolt holds the slip fitted stuffing box in place.
填料箱压盖将密封与填料箱的功能融为一个可更换的整体,一支螺栓安装在与填料箱相对应的中开面上。
The prestress of steel girder by high strength cover plate can raise stiffness and save steel, with simple configuration.
焊接高强钢盖板的预应力钢梁构造简单,刚度较大,节约钢材,是一种值得推广的结构型式。
The performance of the box-type solar collector was investigated experimentally, the cover of which is a high-vacuum plane glass plate with a middle narrow slot.
用窄缝高真空平面玻璃作普通箱式太阳灶的透明盖板,对箱式太阳灶的集热性能进行了实验研究。
However, the Japanese also eat small meals: dishes can only cover a small plate at the bottom, rice and only a Xiaowan.
但日本人正餐也吃得很少:菜只能遮住一个小碟子的底部,米饭也只有一小碗。
Analyzed the forming process of the cover plate, introduced the layout design, and expound design and manufacture process of die structure and its main components.
分析了盖板零件的冲压成形工艺,介绍了零件排样设计方案,阐述了模具结构及其主要零件的设计和制造工艺。
Sprinkle onion and cheese in pie plate. place remaining ingredients in blender. cover and blend on medium - high speed about 30 seconds or until smooth. pour into pie plate.
把洋葱和干酪撒在饼盘中。把剩余的原料放入搅拌器。盖上盖子,中速搅拌约30秒,或是直至匀滑。倒入饼盘。
The ultrasonic transducer vibrates longitudinally, its front cover plate links up with a half wavelength circular conical horn to increase the amplitude of the output end of the ultrasonic transducer.
该超声换能器采用纵向振动方式,其前盖板连接了一个半波长圆锥形变幅杆,以增大超声换能器输出端的振幅。
This article puts forward to lay a cover plate in the welding of the titanium sandwich pressure vessel and it also presents the structure and welding practice of the cover plate.
文章提出了在钛复合板压力容器的焊接中采用盖板敷设焊接,并具体介绍了盖板的结构及其焊接方法。
This article puts forward to lay a cover plate in the welding of the titanium sandwich pressure vessel and it also presents the structure and welding practice of the cover plate.
文章提出了在钛复合板压力容器的焊接中采用盖板敷设焊接,并具体介绍了盖板的结构及其焊接方法。
应用推荐