Descriptors might represent a connection to a device, pipe, or a socket for communicating with another process or to a normal file.
描述符可以表示到设备、管道或套接字的连接，这些连接用于与另一个进程或普通文件进行通信。
A socket functions much like a named pipe but can span hosts.
套接字的功能与命名管道很相似，但是可以跨主机。
Primer is necessary to penetrate and soften both pipe and fitting socket surfaces in order for the solvent cement to properly bond.
有必要采用底漆来渗透和软化管道和管件承插端口表面，使得液状粘固剂能够完全粘结。
This standard covers the procedures for the heat joining of pipe and fittings made from polyolefin materials utilizing either the socket or butt fusion methods.
这个标准涵盖采用承插热熔和对焊热熔方法对聚烯烃材料管道和连接件进行热连接的程序。
PE pipe hot melt socket and hot melt docking interface tensile strength and blasting strength are higher than the pipe ontology.
聚乙烯管件热熔承插和热熔对接接口抗拉强度及爆破强度均高于管材本体。
Ji 'nan stainless steel pipe connection methods are commonly used welding connection, socket welding connection and pipe thread connection.
济南不锈钢管的衔接方法常用的有对焊衔接、承插焊衔接以及管螺纹衔接。
The paper introduces design principle of pipe well using socket and spigot connected cast iron pipes as pipe material. The results are effective.
论述了承插式铸铁管作井管的优点和设计原理，实践证明效果良好，值得推广。
Hot melt welder: PE pipe and PE pipe links, mainly USES the hot melt socket, hot melt docking and wire teeth three ways.
热熔焊机：聚乙烯管件与PE管材的链接，主要采用热熔承插，热熔对接和金属丝牙三种方式。
The embedding part includes volute socket ring, tail water taper pipe, tail water ell, pit liner and so on.
埋入部分包括蜗壳座环、尾水锥管、尾水肘管、机坑里衬等。
The distribution of chemical composition and microstructure for cracking socket of centrifugal cast ductile iron pipe, and the effect of them on the cracking behavior have been studied.
分析了离心球铁管开裂承口的组织、成分分布，探讨了组织、成分对承口开裂的影响。
High Strength bolts: all kinds of grade 10.9 and 12.9 high strength hex and hex socket screws, bolts, sleeves, pipe plugs, shoulder screws, stainless steel hex socket bolts, set screws.
高强度螺栓类：库存各种规格的10.9级、12.9级高强度内外六角螺丝、螺栓、套筒、喉塞、塞打、不锈钢内六角螺栓、刀把螺丝、机米。
The draining socket bolt is installed on the lower end of a draining pipe and is connected with a faucet of the draining pipe.
将排水插口栓安装在排水管下端与排水管承口相接。
The pipe fitting is divided into a socket part (1) of two ends connected with a tube and a central bending part (2).
将管件分成与管子连接的两端的承插部分（1）和中间的弯曲部分（2）。
The pipe fitting is divided into a socket part (1) of two ends connected with a tube and a central bending part (2).
将管件分成与管子连接的两端的承插部分（1）和中间的弯曲部分（2）。
应用推荐