How do I record packets received or transmitted?
如何记录接收或发送的数据包？
Ipkts: the total amount of packets received by the interface.
Ipkts：该接口所接收到的数据包的总数。
The iptrace command records all the packets received from the network interfaces.
iptrace命令记录从网络接口接收到的所有数据包。
Then, use tcpdump to display packets received from the host using the example shown in Listing 17.
然后，使用tcpdump显示从此主机接收的数据包，见清单17。
To record packets received on an interface en0 from a remote host airmail over the telnet port, enter
要想记录en0接口上通过 telnet端口从远程主机airmail 接收的数据包，输入
The output from the /sbin/ifconfig/eth0 command lists a total of all packets received and transmitted.
sbin/ifconfig/eth0命令的输出将列出收到和传输的所有信息包总数。
A ping fails when the number of packets received is less than the number sent and packet loss is greater than 0 percent.
当收到的数据包数量少于发送的数量，数据包损失大于0时，ping失败。
For example, the -d option shows the overall number of packets received, transmitted, and dropped in your communication subsystem.
例如，- d选项将显示您的通信子系统所接收的、传输的和丢弃的数据包的总数。
A problem addressed is the complexity imposed by a soft handover combination node in the network for combining packets received from one mobile station over parallel diversity links.
提出的一个问题是由网络中用于组合通过并行分集链路从一个移动台接收的分组的软切换组合节点造成的复杂性。
Red packets are always presented and received with both hands.
红包总是用双手送出和接收。
However, those larger average Windows also mean the SACK receiving code needs to do a lot more work for every packet received as the queue to be scanned contains more packets.
可是，这些较大的平均窗口也意味着SACK接收代码需要对收到的每个包做很多工作，因为需要扫描的队列包含更多的包。
In short, this driver provides user-space access to the Ethernet device so that packets can be transmitted and received.
简单地说，这个驱动程序提供对以太网设备的用户空间访问，这样就可以发送和接收数据包。
The important rows are those beginning RX and TX, which show information about the packets sent and received.
以RX和TX开头的行很重要，它们提供关于发送和接收的数据包的信息。
If the error rate is excessively high compared to the packets transmitted or received, then it may indicate a fault with the network hardware.
如果与传输或接收的数据包相比错误率很高，可能说明网络硬件有问题。
Use tcpdump to display packets sent to and received from the host on the specified port using the example shown in Listing 12.
使用tcpdump显示发送到主机上的指定端口或从其接收的数据包，见清单12中的示例。
In such cases, getting statistics like number of packets sent or received and the number of RPC calls sent or received by that interface helps in debugging.
在这种情况下，获取统计数据有助于调试，比如接口发送或接收的数据包数量和发送或接收的RPC调用数量。
This obtains a number of data points from a specified SNMP agent, including the IP address, description, uptime, and network statistics (packets sent/received, and IP packets sent/received).
这将从指定的SNMP代理获得许多数据点，包括IP地址、描述、正常运行时间和网络统计数据（已发送/接收的数据包和已发送/接收的 IP 数据包）。
This is because the links are Shared and packets must be entirely received at one switch before moving to the next.
因为连线是被分享，并且封包一定要被一个交换器完全地收到后才会移动到下一个交换器。
UDP received data packets but prints out funny results.
UDP接收数据分组的可打印出有趣的结果。
Receive data from serial analysis of received packets, and then computing algorithm, and finally return the results from the serial port.
从串口接收数据，分析收到的数据包，然后根据算法进行运算，最后将结果从串口返回。
One embodiment includes using one equalizer for training while using another equalizer for processing received data packets.
一个实施例包括使用一个均衡器用于训练而使用另一个均衡器用于处理接收到的数据分组。
It avoids to process extension header for each received packets, then increases the processing efficiency.
避免了对每个报文的包头选项处理，提高了处理效率。
This means that in such an environment, to a host of data packets will be all other machines received.
这意味着在这样的环境中，发给某个主机的数据包也会被其它所有的机器收到。
In one example, while the equalizer receiver 34a trains for one user, a second equalizer receiver 34b processes a received signal containing data packets from a previously scheduled user.
在一个例子中，当均衡器接收机34A为一个用户训练时，第二均衡器接收机34B处理接收的信号，该接收的信号包含来自先前调度的用户的数据分组。
The receiver performs the complementary processing on the received PHY packets to recover the MUX-PDUs.
所述接收机对已接收的物理层包执 行互补处理以恢复所述多路复用协议数据单元。
The server read the framed RTP data packets from the source server, send to many connected players, and then make use of the received report returning from the players to adjust to the sending rate.
服务器从数据源读取已封装完成的RTP数据包，以组播方式发送给众多客户端，利用用从客户端返回的接收报告调整发送速率。
The server read the framed RTP data packets from the source server, send to many connected players, and then make use of the received report returning from the players to adjust to the sending rate.
服务器从数据源读取已封装完成的RTP数据包，以组播方式发送给众多客户端，利用用从客户端返回的接收报告调整发送速率。
应用推荐