PA6 serial TPAE is a kind of important products in TPAE.
聚酰胺6热塑性弹性体是TPAE中重要的一类产品。
The rate of dye-uptake of modified PET is improved, but is still far lower than PA6.
改性聚酯对酸性染料的上染率有一定的提高，但与PA6的上染率相比仍有差距。
Composite was prepared with melt dipping that PA6 enhanced with the long glass fibre.
采用熔体浸渍工艺制备长玻纤增强PA 6复合材料。
Material could be steel, stainless steel, aluminum, copper, nodular casting iron and PA6.
材料可钢，不锈钢，铝，铜，球墨铸铁铸造生铁和锦纶。
It can improve mechanical performance by adding PPg - (St-MAH) to PP and PA6 blend systems.
加入到PP和PA 6共混体系可以改善PP和PA6的相容性和提高机械性能。
The effect of compatilizer and toughener on the properties of modified PA6 /PA66 is studied.
研究了相容剂、增韧剂对改性尼龙6/尼龙66合金性能的影响。
With the adding of PA6 and UHMWPE, the modulus of PA6/UHMWPE/HDPE blend is changed evidently.
PA6和UHMWPE含量的增加对共混物的初始模量有显著影响。
And then, a few problems for the further research in PA6 polymerization process are pointed out.
在此基础上，提出了PA 6聚合反应工程研究中尚有待开展的几点建议。
This Paper introduced H4S process for producing PA6 full-drawn yarn based on the production principle.
本文从生产原理上介绍H4S工艺生产锦纶6全牵伸丝的生产过程。
Flame retarded fiberglass reinforced PA66 and PA6 were prepared by adding melamine polyphosphate (MPP).
采用聚磷酸三聚氰胺（MPP）分别对玻纤增强的PA66和PA6进行了阻燃。
The cleaning result has proved to be successful for regularly spun or high speed melt spun PET PA6 and fiber.
清洗效果表明，该方法简单、方便、见效快、效果好，可用于锦纶、 涤纶等常规或高速纺熔体管道的清洗。
The processability of rare-earth magnetic materials with 7 wt% PA6 was studied by using HAAKE torque rheometer.
应用HAAKE转矩流变仪，研究了尼龙6质量分数为7%时，稀土磁性塑料的加工工艺性能。
PA6/easy hydrolytical polyester(EHDPET) blend fiber with EHDPET as disperse phase was prepared by blend spinning.
将PA6和易水解聚酯（EHDPET）以适当比例混合，可制得以EHDPET为分散相的共混纤维。
The design of PA6 prepolymerization reactor was discussed from the aspects of equipment and technological process.
从设备与工艺两方面剖析了PA6生产前聚合反应器的设计。
Both the feasibility and the processing result of vacuum polymerization finishing process for PA6 fiber were discussed.
分析探讨了采用减压后聚合工艺生产pa6的可行性及实施效果。
The results showed that the use of PA6 improved the apparent viscosity, mechanical properties and thermostability of IFR-PP.
结果表明：PA6的加入提高了IFR PP的表观粘度、力学性能和热稳定性。
The melting temperature of PA6/PTFE blends increases with PTFE content, while the melting enthalpy decreases with PTFE content.
PTFE共混物的熔融温度随PTFE含量的增加而升高，熔融焓却随PTFE含量的增加而降低。
The formulations, mold selection and technical conditions for preparing the flame-retardant & reinforced PA6 and PA66 are studied.
探讨了阻燃增强PA6及阻燃增强PA66的制备配方、模具选择及工艺条件。
The crystallization behavior of rare-earth luminous polycaprolactam(PA6) prepared through in-situ polymerization was investigated by DSC.
以原位复合方法合成的稀土发光聚己内酰胺（PA6）为研究对象，用差示扫描量热仪（DSC）研究了其结晶行为。
The rheological behaviors of PA6/clay nanocomposites by in situ polymerization and PA6 were studied with Instron 3211 capillary rheometer.
采用毛细管流变仪测定了原位聚合的PA6/粘土纳米复合材料及PA6的流变性能。
The interfacial interaction of compatibilized PP/PA6 blend prepared by melt grafting of PP with MAH and other unsaturated acid has been studied.
采用PP熔融接枝MAH和不饱和羧酸混合单体通过反应挤出增容PP/PA6共混物，研究了增容共混物两相间的界面相互作用。
The relationship between Brookfield viscosity and temperature, dip pick-up and adhesive strength of dip solution for PA6 tire cord was discussed.
讨论了锦纶6帘子布浸胶液布氏粘度与温度、附胶量、粘着强度的关系。
The results showed that the range of the region of phase co-continuity PS/PA6 was 40/60-65/35 at experimental temperature, rotor speed or mixing time;
结果表明在一定螺杆转速、共混温度、共混时间范围内，PS/PA6共混物形成双连续相组分的比例范围为40/60—65/35；
Hagrid set up a paddock for hippogriffs in an area like this (PA6) and the dragons which had been brought in for the First Task were chained here (GF19).
海格在那个地方建了个小围场，以便给鹰头马身有翼兽生活（囚徒，第六章），而为了第一个任务中带来的龙，也被拴在这里。 （火焰杯，第十九章）。
The effect of surface isocyanation of carbon fiber on the melting behavior of PA6 in CF/PA6 composites was studied by Differential Scanning Calorimetry(DSC).
利用差示扫描量热仪（DSC）研究了炭纤维（CF）表面异氰酸酯化改性后阴离子接枝尼龙6（PA6）对CF/PA6复合材料中PA6的多重熔融行为的影响。
In terms of the PA6 + 60% GF wear and corrosion properties of material, we choose the special materials and special gate structure to prolong system longevity.
针对PA6+60%GF的材料的磨损和腐蚀特性，我们的热流道系统选用了特殊的材料及特殊的浇口结构，以保证系统的使用寿命！
The results showed that the dimensional stability of PA6 guide sleeve was greatly improved and the developed Nylon composite for the guide sleeve met the per-fom…
试验结果表明，尼龙6导向套产品的尺寸稳定性得到了大幅度的改善，研制的导向套用尼龙复合材料满足了产品的性能要求。
The results showed the use of PA6 upgraded the mechanical properties and thermal stability of the composite, and PA6 had obvious synergistic effect on the system.
结果表明：PA6的加入提高了该体系的力学性能和热稳定性，并对该无卤阻燃体系具有良好的协效作用。
The results showed the use of PA6 upgraded the mechanical properties and thermal stability of the composite, and PA6 had obvious synergistic effect on the system.
结果表明：PA6的加入提高了该体系的力学性能和热稳定性，并对该无卤阻燃体系具有良好的协效作用。
应用推荐