This means that you can redirect output to a remote command.
这意味着您可以将输出重新定向到远程命令。
This command produces the output shown in Listing 4.
这个命令生成的输出如清单4所示。
This command produces the output shown in Listing 5.
这个命令生成的输出如清单5所示。
The output of the command should tell you the host name assigned to this IP address.
这个命令的输出应该告诉您分配给这个IP 地址的主机名。
You can pipe output from one command to another using pipes, |.
您可以用|管道将来自一个命令的输出送到另一个命令。
The greater than sign (> allows you to redirect output from the command.
大于符号 >允许您对该命令的输出进行重定向。
Listing 2 shows the output of this command.
清单2列出了这个命令的输出。
You may be wondering what happens to any output from the command.
您可能想知道对来自命令的输出会如何处理。
When you are passing parameters, particularly if they are the result of command output, things can be tricky.
当您传递参数时，尤其当这些参数是命令的输出时，处理起来可能需要些技巧。
The output of this command describes the parameters of the file system.
该命令的输出描述了文件系统的参数。
The output from this command should help the network administrator determine whether there's a real routing issue.
这个命令的输出应该有助于网络管理员判断是否真的有路由问题。
Highlights of the command and output are discussed.
我们将讨论高亮显示的命令及输出。
The command output indicates some logs located on the master and slaves.
命令输出指出主节点和从节点上的一些日志。
The output of the command indicates the Map and Reduce process.
命令的输出说明映射和缩减过程。
Listing 10 shows the command being run and the output of the command.
清单10显示了需要运行的命令及其输出。
Listing 4 shows the program output from this command.
清单4展示了这一命令的程序输出。
Listing 1 shows this command and its output.
清单1显示了这个命令以及输出。
The output of a command is a noun — data to be perused or used.
命令的输出是名词——要查阅或使用的数据。
Listing 1 shows typical output from this command.
清单1显示了此命令的典型输出。
Listing 1 shows the output from this command.
清单1显示了此命令的输出。
To the bottom are the breakpoints for the debugger, the command output, and so on.
下面是调试用的断点、命令输出等等。
Output of the command LLQ, on node ha2, after failover.
失效切换后，在节点ha2上llq命令的输出。
Figure 6. Command-line output of sender application.
图6.sender应用程序的命令行输出。
Figure 7. Command-line output of receiver application.
图7.receiver应用程序的命令行输出。
Command-line output of receiver application.
receiver应用程序的命令行输出。
Command-line output of sender application.
sender应用程序的命令行输出。
Listing 9. Output from define template command.
清单8.definetemplate命令的输出。
Listing 10. Output from list repl command.
清单9.list repl命令的输出。
Listing 11. Output from list replset command.
清单10.list replset命令的输出。
Listing 25. Output from the lsgroup command.
清单25.lsgroup命令的输出。
应用推荐