The optimum thickness of ceramics samples for electromagnetic wave absorption was calculated.
对先驱体陶瓷样品的吸收厚度进行了优化计算。
The optimum thickness of the coating is determinedby the simnlation experiments on the ground.
通过地面模拟实验确定了涂层的最佳厚度。
Research on the optimum thickness of metallic thin film utilized to excite surface plasmon resonance;
研究了拉锥光纤表面等离子共振氢敏感机理、构建及应用。
The optimum thickness for the insulating layer is to find the optimal solution for a nonlinear objective function.
保温层厚度的优化是含有多变量非线性目标函数的优化。
The optimum thickness of thermal insulation are decided through calculation, so that lowest heat loss value can be reached.
同时对保温层厚度及散热损失等进行了设计计算并与实测散热损失值做了对比。
The optimum thickness of transmission-mode photocathode is analysed theoretically, and the methods for monitoring and determining the optimum thickness are proposed.
并提出了确定最佳厚度的监测和计算方法。 最后给出了多碱光阴极在几个给定工作波长的最佳厚度。
It is pointed out that each belt drum diameter is corresponding to an optimum belt thickness, and steel belt with optimum thickness should be coiled to obtain the maximum fluid lift.
指出每种绕带滚筒直径均对应一个最佳钢带厚度，不同直径的滚筒应卷绕厚度最佳的钢带，以获得最大的举液高度。
Optimum design of focused transducers is studied, and the selection of thickness of lens and materials is discussed.
研究了聚焦换能器的优化设计，对透镜厚度及材料的选取进行了分析。
By comparison of the influence of some technical parameters on the thickness, along with the executive feasibility analysis, the optimum project for changing the film thickness was obtained.
通过对比几种工艺参数对膜厚的影响及实施的可行性分析，最终得出改变漆膜厚度的最佳方案。
Optimum profile, shape and thickness difference of strip can be obtained by means of changing stress distribution of load on the surface of strip.
通过改变轧辊、板带表面的应力分布，来得到理想的带材凸度、板形和厚差。
The first optimum model is established with the target function of the frame's weight as well as with the design variables of the beam's single layer thickness.
首先以纵梁各部分单层厚度为设计变量，建立了以车架重量为目标函数的优化模型并进行了优化研究，取得了较好的优化效果。
Based on GB 150-1998, a mathematical optimum design model of wall thickness and exterior strengthen structure for rectangular pressure vessel was established.
在GB 150—1998《钢制压力容器》标准上建立矩形截面容器筒体壁厚和刚性外加强圈的优化设计模型。
Meanwhile, the economic flow rate, optimum diameter and economic insulating layer thickness of the equipment and pipeline have been obtained with the model, which provide a basis for pipeline design.
该模型将同时得到经济流速、设备及管道最佳直径和经济保温厚度，可作为管道工艺设计的基础；
Optimization of overlay thickness taking into account of lifecycle and one period performance is discussed with several design nomograms of optimum overlay thickness provided.
文中考虑了寿命周期和一个性能期罩面厚度的优化，给出了几个性能期最佳罩面厚度设计诺谟图。
Based on the objective function, local optimum and iterative method were adopted to get a computer solution on the optimum economical thickness.
对保温设计的目标函数，采用局部求优，逐步迭代的方法，实现了多层保温经济厚度计算机求解。
This article has made scientific researches on the optimum of process for veneer rotatory-cutting, and obtained the optimum technologies for two kinds of veneer thickness of linden.
本文在单板旋切工艺最优化方面进行了研究得出椴木两种单板厚度的最佳工艺条件。
Enter the pipe diameter, wall thickness and pipe material, and the PT500 calculates the optimum mounting method and separation distance for the sensors.
输入管径，壁厚，管道材料，以及PT 500计算出最佳的安装方法，传感器和分离的距离。
It also discusses the method of calculating the film thickness and the method of optimum design and also the technological process of manufacture of the seal.
论述了计算油膜厚度和结构优化设计的方法以及实现该结构的工艺手段。
The influences of the reflective coefficient of the double layer soil, the top layer soil thickness and the grounding grid area on the optimum arrangement are analyzed numerically.
论文采用数值计算的方法分析了双层土壤结构时土壤反射系数、上层土壤厚度及地网面积大小等因素对地网最优布置的影响规律。
From the view of life cycle and economics the optimum insulation thickness of hot air pipes in industrial furnaces is discussed.
从寿命经济学观点出发，讨论了工业炉热风管道最佳保温层厚度的问题。
The paper introduces the determination of the optimum weir space, the thickness and application limits of the technique and matters needing attention during application.
介绍了垄向区田技术中最佳垱距、土垱厚度、应用范围的确定及其应用中应注意的问题。
The paper introduces the determination of the optimum weir space, the thickness and application limits of the technique and matters needing attention during application.
介绍了垄向区田技术中最佳垱距、土垱厚度、应用范围的确定及其应用中应注意的问题。
应用推荐