The operating error was due to carelessness pure and simple.
操作失误纯粹归因于粗心大意。
Cosmetic surgery operating error and maintenance of nursing error and may cause surgical failures.
整容手术操作失误及保养护理失误，可能导致手术失败。
Fixing a cutting tool in best direction will make the operating error smallest. This direction can be obtained by fixing and testing the measured element only one time.
镗床类主轴在最佳方位上装刀，可使加工误差最小，此方位只需被测元件一次安装和测试即可求出。
If the specified name is defined in the operating system as both, an error is returned.
如果指定的名称在操作系统中同时定义为用户和组，那么返回一个错误。
Perhaps it's a logic error or an error caused by interacting with the operating system or both.
可能它是一个逻辑错误和/或与操作系统进行交互所导致的错误，或两者兼具。
When you attempt to link 32-bit objects against the 64-bit DB2 application library, an operating system linker error message is returned.
当您试图将32位的对象链接到64DB 2应用程序库时，将会返回一条操作系统的连接程序出错消息。
The operating system imposes a limit on the amount of memory that can be locked. When this limit is reached, the overlapped operations will fail with the WSAENOBUFS error.
操作系统有一个锁定最大数的限制，一旦超过这个锁定的限制，那么就会产生WSAENOBUFS错误了。
Until you are sure that things are operating as you intend, allow logins to continue in case of an error.
直到确保所有的事情都能按预期运行之后，才允许在出错的情况下继续登录。
Could not access console mutex. Operating system error % 2.
未能访问控制台互斥标志。操作系统错误%2。
Error loading operating system. Setup cannot continue.
加载操作系统时出现错误。安装程序无法继续。
Error that caused slowdown in operating system loading has been fixed.
在操作系统的装货导致减速的错误被改正了。
操作系统错误 %2。
The application has an excellent response time and smoothly integrates into the operating system, without causing it to hang, crash or pop up error dialogs.
该应用程序有一个很好的响应时间，顺利地集成到操作系统中，而不会导致其挂起，崩溃或弹出错误对话框。
It is distinct from the operating range, within which the instrument will provide a measurement but the error is not well-defined.
测量范围和工作范围不同，在工作范围内，仪器可以测量但是不能很好地定义误差。
A nonfatal error can be detected and investigated by a part of the operating system or run-time system and the results can be displayed or used to make a programmed decision.
非致命错误可以用操作系统或运行时系统的一部分进行检测和研究，结果可以显示出来，也可以用于进行程序判断。
For operating easily, a wizard compensation program is designed to correct every error and to get the optimum compensation.
为了方便操作，系统还设计了向导式的工作界面。
The excellently good ceramic physics performance guaranteed the stable performance under ambient temperature and the high operating temperature, with small size error and outstanding quality.
极佳的陶瓷物理性能，保证在环境温度和高的工作温度下性能稳定，尺寸误差小、表面质量优秀。
Analysis and operational Suggestions are made on measurement error of moving-coil instrument for thermo -coupling resulted from abnormal operating conditions.
本文分析了配热电偶用动圈式仪表在非正常使用条件下产生的测量误差，并提出了操作建议。
Different from the common inverse time characteristic, this model conforms to the load actual operating law and the protection request, and takes the analysis of measurement error into consideration.
与常用反时限保护特性相比较，此保护模型更符合负载的实际运行规律及保护要求，并对测量误差关系进行了分析。
This paper introduced the error sensitive index for evaluating the operating accuracy of parallel robots, which reflects the degree of the robot mechanism's solution for the original error.
本文引入了并联机器人误差敏感系数，它反映了机器人机构的解对原始误差的敏感程度。
This paper introduces the operating principle and design idea of standard level instrument and briefly analyzes its error.
着重介绍了水平标准器的工作原理及设计构思，并对仪器的误差作了简要分析。
Quantum bit error rate is an important operating parameter in quantum key distribution.
量子误码率是量子密钥分配系统的重要参数之一。
Results shows the following fact: it can be guaranteed that the practical tracking error in operating process of rigid robot manipulator attenuates to the given region around the origin.
采用文中给出的鲁棒控制器，能保证机械臂的实际跟踪误差在有限时间内减少到预先给定的包含原点为内点的区域。
The operating principle, the error analysis, the calibrating process and its results of calibration are introduced in the paper.
该文介绍了恒湿盐湿度发生器的工作原理、误差分析、检定过程和标定结果。
The operating noises of the gear pump are mainly from the perturbations of mass flow rate and the pressure, which result in the error of gear teeth geometry contact during the rotation.
齿轮泵中轮齿啮合几何学上的原因所造成的流量脉动及其相应的压力脉动是产生噪声的主要原因之一。
This Recommendation defines error performance parameters and objectives for international digital connections operating below the primary rate of the digital hierarchy.
本建议规定了工作在低于数字系列的一次群速率的国际数字连接的差错性能参数和指标。
This paper introduces the operating principle of manufacturing complex surface in 5-axis nc machine. It is emphasis on error model of complex surface by ring mill cutter in 5-axis nc machining.
介绍了五轴数控机床加工复杂曲面的工作原理，重点分析了五轴数控加工时采用环形铣刀加工复杂曲面的误差模型，提出了误差补偿的具体方法。
At run time, if the operating system is unable to load the program at that address, it issues an error message and does not load the program.
在执行阶段时，如果作业系统无法将程序载入该位址，它便会发出错误讯息而且不会载入程序。
At run time, if the operating system is unable to load the program at that address, it issues an error message and does not load the program.
在执行阶段时，如果作业系统无法将程序载入该位址，它便会发出错误讯息而且不会载入程序。
应用推荐