Pull and hold the stainless steel wire at the top which opens the valve, allowing the liquid to flow in.
拉按住不锈钢丝上方的打开阀门，使液体源源不断的流进采样器。
Engagement between the spring arms and the sliding surface creates a lifting force which opens the valve.
该弹簧臂与所述滑动表面之间的接合产生了开启所述阀的上举力。
3 SEC The PORV (pressure relief valve) opens automatically, releasing steam into a holding tank.
3秒减压阀自动打开，将蒸汽释入一个储存罐。
The timer then opens the lower valve for a fixed period of time, permitting the - plastic powder to discharge from the intermediate chamber.
定时装置随后开启下面的夹管阀并持续一段固定的时间，让塑料粉末从中间罐腔中排出。
AW pneumatic actuator used, make sure the valve opens, closing torque, and then do the valve using a fluid medium, added security value.
选用AW气动执行器时，先确定阀门启、闭的扭矩，再根本阀门使用的流体介质，增加安全值。
Then the controller opens the solenoid valve and starts the pump pressure, the water will be closed after the two will be closed.
这时控制器打开电磁阀并启动水泵加压，待水上满后两者将会同时关闭。
Raised-face seat. A groove around the seat collects particles pushed aside by the knife and prevents clogging. When the valve opens, media pressure cleans the groove.
凸面阀座。阀座周围的槽将颗粒收集起来，并排挤到闸刀旁边，以避免出现堵塞。当阀门开启时，流体介质压力就会清洗槽内的颗粒。
When in work, the control system automatically opens or closes the gate of the electric flashboard valve according to the signals sent by the material level meters.
工作时，控制系统根据料位仪传来的信号自动开启或关闭电动闸板阀闸口。
Whenever the oil pressure exceeds the maximum pressure, the regulator valve opens to reduce the pressure.
每当油压力超出最大压力时，打开调节阀，以减少压力。
The fuel injector is basically a tiny electric valve, which opens and closes with an electric signal.
油器通常是一个较小的电动阀，由电信号控制打开和关闭。
When cold WFI is needed, the cooling mode (fig. 5) is turned on by an air switch, which closes the recirculation valve and opens the cooling water valve. Within seconds cold WFI is available.
当需要冷却注射水时，系统通过一个空气开关打开冷却模式（图5 ），同时关闭了循环水阀门打开了冷却水阀门，只需几秒钟，就可以得到冷却注射水了。
This downward movement forces the valve to move downward off its seat so that it opens.
向下的运动使气门向下移动离开气门座，气门被打开。
In a straight travel valve of the hydraulic control apparatus, a communication path and a control valve that opens and closes the communication path are provided.
在液压控制装置的直线行驶阀中设置连通路径以及开启和闭合连通路径的控制阀。
To the hydraulic jack interior module's unique design, after having realized the valve core opens completely, causes the gas free from obstacle passing.
对液压千斤顶内部组件的独特设计，实现了阀芯完全打开后，使得气体无阻碍的通过。
As the piston reaches BDC again the exhaust valve opens.
当活塞再一次到达下止点时，排气门打开。
As the piston reaches BDC again, the exhaust valve opens.
当活塞再一次到达下止点时，排气门打开。
First opens the by-pass valve counter-pressure, then operates the valve, latter opens the hydraulic turbine.
先开启旁通阀平衡压力，再开阀，后开启水轮机。
The ball valve is opens by the spherical achievement shuts a valve.
是以球状件作为启闭件的阀门。
Stay-Open valve: a valve that manually opens and closes the emergency units.
打开球阀：手动打开紧急洗眼装置的球阀。
When the valve outlet pressure to a pilot valve spring set pressure, pilot valve opens, the control room to the downstream drainage.
当阀门出口压力降到导阀弹簧设定压力时，导阀开启，控制室向下游排水。
The valve opens automatically by pressurizing connection 1.
阀门打开自动加压连接1。
In between, an electromagnetic vacuum inflation valve is installed in series, which opens and closes with the switch of the pre-stage pump.
在前级泵与主泵中间串联一个电磁真空充气阀，随前级泵开关而启闭。
Manual pumps USES in under the system debugging and the special operating mode valve opens shuts.
手动泵用于系统调试和特殊工况下的阀门启闭。
Intake stroke: the camshaft opens the intake valve and the piston moves down the cylinder. This creates vacuum and sucks in air and fuel into the combustion chamber above the piston.
进气行程：凸轮轴打开进气阀，活塞在汽缸中向下运动，产生一段真空。
The gate valve usually is at the off-position, the water pump starts when the gate valve opens slowly, when water pump engine off, the gate valve shuts down slowly first.
闸阀平时是处于关闭状态，水泵启动时闸阀慢慢打开，水泵停机时，闸阀先慢慢关闭。
At the same time the valve opens a small moment, to achieve the rapid opening and closing the valve.
同时阀门开启矩小、能实现阀门的迅速开启和关闭。
Opens pours water the valve to the pump, and waits for three minutes, guarantees in the driving fluid inflow pump;
打开向泵内注水阀门，并等待三分钟，确保工作液流入泵内；
Opens pours water the valve to the pump, and waits for three minutes, guarantees in the driving fluid inflow pump;
打开向泵内注水阀门，并等待三分钟，确保工作液流入泵内；
应用推荐