Burning fuels such as coal and oil pump vast amounts of greenhouse gases into the atmosphere.
燃烧煤炭和石油这类化石燃料会产生大量的温室气体。
The single screw oil pump is a new type extracting oil pump, which is simple in structure and high in performance with low working cost.
单螺杆抽油泵是一种新型的采油泵,结构简单,性能可靠,作业成本低。
After the oil pump motor finishes starting, the pump is loaded.
油泵电机起动完毕后对泵进行加载。
Light oil pump house is mainly used to convey some volatile and inflammable oil products.
油库轻油泵房主要输送易蒸发、易燃烧的油品,属于爆炸危险场所。
Sintered properties of the oil pump gears and part to part consistency are also reported.
还报告了油泵齿轮烧结后的性能和零件间性能的均一性。
The mechanical seal leakage of hot oil pump has always been an important problem for oil refineries.
热油泵机械密封的泄漏一直是炼油厂关注的重要问题。
Press "start" switch, oil pump starts to run, press "stop"switch, oil pump stops running immediately.
按动“启动”开关,油泵开始运转,再按”停止“开关,油泵立即停止运转。
The main reason of compressor shutdown in normal replacing oil pump is analyzed combining with practice.
结合实际分析了正常倒换油泵过程中压缩机停车的主要原因。
The affinity law of impeller trim for the centrifugal oil pump 65y60 is gained when pumping viscous oil.
得到了输送粘油时65y60型离心油泵的叶轮切割规律。
The welded metal bellows mechanical seal is largely used for the axial seal of hot oil pump in refinery.
焊接金属波纹管机械密封主要用于炼油厂热油泵的轴封。
Operation test of emergency switching-off device for oil pump and ventilator (bilge pump) in engine room.
机舱风、油(舱底泵)应急切断装置操作试验。
Pre-heating oven. Oil heating for bronzing plate, constant temperature auto control, oil pump circulation.
烫金版油加热,恒温自动控制,油泵循环。
The downhole oil water separation system is comprised of double fluid flow pump, cyclone separator and oil pump.
井下油水分离系统由双液流泵、旋流分离器和原油提升泵三大部分组成。
A design method of the rotor oil pump is presented, and an example is provided to describe the design procedure.
介绍了转子机油泵的设计方法,并以实例说明了设计过程。
Check 3-way fuel oil selection valve located before fuel oil pump unit and change the 3-way valve to MDO/MGO side.
检查位于燃油输送泵前的三通燃油切换阀,并转换到MDO侧。
The influence of the number of blades on the affinity law of impeller trim for the centrifugal oil pump is obtained.
得到了叶片数对离心油泵叶轮切割定律的影响规律性。
The oil pump has the important task of delivering an adequate volume of oil around the engine at a suitable pressure.
机油泵一个重要的任务是给发动机提供足够量的、压力适当的机油。
The fixed value of swing type of oil pump rotor is an important target for controlling and inspecting rotors quality.
摆线型机油泵转子的定值是控制和考核其质量的一个重要指标。
Domestic main oil pump thrust tile of 300mw steam turbine wears and tears the trouble, happen timely in recent years.
国产300MW汽轮机主油泵推力瓦磨损故障近年来时有发生。
External motor and oil pump enable good ventilating and cooling conditions, safety operation and prolonged service life.
由于电机、油泵外置,其通风冷却条件好,运行安全,寿命长。
External motor and oil pump enable good ventilating and cooling conditions, safety operation and prolonged service life.
由于电机、油泵外置,其通风冷却条件好,运行安全,寿命长。
Proper selection of heating furnace, fuels, cycle oil pump, heat medium and control of reactor temperature were discussed.
讨论了热媒加热系统中的加热炉、燃料、循环油泵、载热体和釜温自控的选择原则。
In addition, the camshaft has an eccentric to operate the fuel pump and a gear to drive the ignition distributor and oil pump.
此外,凸轮轴还带动一个驱动燃料泵的偏心轮和一个带动分电器和油泵的齿轮。
The fracture surface of a failed injection valve nut of diesel engine high pressure oil pump was investigated by visual and SEM.
对断裂的汽车柴油机高压出油阀紧座的宏观、微观断口及显微组织进行了研究。
The key to the technological transformation is the design of the manual oil pump, the delivery pump and the whole transmission box.
技术改造的关键是手油泵、输油泵及传动箱总成的设计。
The key to the technological transformation is the design of the manual oil pump, the delivery pump and the whole transmission box.
技术改造的关键是手油泵、油泵及传动箱总成的设计。
Press the starting button of the oil pump on the operation box beside the Hydraulic Bump Station. Note: only start one oil pump motor.
按位于液压泵站旁操纵箱上的油泵起动按钮,只起动一台油泵电机。
Flexibility design method of large scale hot oil pump inlet piping is expounded as well as the layout of pipeline, support and hanger.
介绍了大型热油泵入口管系的柔性设计方法、管道的布置方式、支吊架的设置方式。
Flexibility design method of large scale hot oil pump inlet piping is expounded as well as the layout of pipeline, support and hanger.
介绍了大型热油泵入口管系的柔性设计方法、管道的布置方式、支吊架的设置方式。
应用推荐