At last the path planning method, subarea zigzag, contour offset path and combination of them used in PDM and the path generation are described.
阐述了在PD M中采用的路径规划方式，分区折线、轮廓等距偏移和两者的复合方式，并说明了其路径的生成方法。
Any query such as the one in Listing 1 has a precise path to the specified datum, which a DBMS can quickly determine in balanced trees and byte-offset codings.
如清单1中所示的任何查询都有到指定数据的精确路径，DBMS可以迅速地在均衡树和字节偏移编码中确定它。
The RAWDEVSIZE program analyzes available raw devices and stores the offset, size, and path information of free blocks into a database table named free_chunks.
RAWDEVSIZE程序分析可用原始设备，并将空闲块的偏移量、大小和路径信息存储到一个名为free_chunks的数据库表中。
If either of those values needs to be changed, the entry will have to be deleted and re-added with the new path, the offset, or both. The syntax for the modify command is as follows.
如果需要更改两个值中的任何一个，就需要删除条目并重新添加新路径、偏移量或两者。
The principle and method was introduced of identifying cutter offset direction and calculating cutter path according to vector operation.
介绍了通过矢量运算方法对立铣加工刀具偏移方向和刀具轨迹进行快速自动判别和计算的原理和方法。
Meanwhile, in different working condition, the measuring of the same noise transfer path gives results that have minor offset of peak values positions between each test.
通过对不同的工况下同一噪声传递路径的测量分析，发现了传递函数的峰值存在频率偏移。
In some circumstances, the digital offset in the digital domain may be applied at substantially all times of operation of the audio signal path.
在一些情况下，可在所述音频信号路径的大致所有操作时间应用所述数字域中的所述数字偏移。
But to layered strata, the seismic wave path is complicated when reservoir changes, and it is difficult to directly define vertical time difference by pre stack far offset seismic data.
对于层状介质，油藏变化前后的地震波传播路经比较复杂，其激发点和接受点发生了变化，要想用叠前远偏移距数据直接计算垂直时差比较困难。
Furthermore, equation of offset surface from the reconstruction would make easy planning for cutting tool path in NC machining of the radome.
求算的等距面方程，为数控加工中刀具轨迹的规划奠定了基础。
A new style of contour parallel tool path, which is called uneven offset tool path, for free form pockets machining is developed in this paper.
提出用于型腔加工的一种新型刀轨计算方法——非均匀偏置算法。
The algorithm had been compiled in the developed RPM data processing software. Using the new algorithm, the stability is improved and the OFFSET tool path can be generated in the RPM process.
该算法在已开发的RPM数据处理软件中得到成功应用，可提高已有数据处理软件的稳定性，实现了RPM的OFFSET加工轨迹的生成。
In contrast to other algorithms, this method is able to derive explicit formulas to compute paths and generate path trajectories on all offset surfaces for final component forming.
与其他方法相比较，该算法推导出了明确统一的路径公式，可用于生成铺丝轨迹；由于是基于多层曲面上的路径生成，因此可用于构件的最终成型。
The device consists of a precision, low-offset linear Hall sensor circuit with a copper conduction path located near the surface of the die.
该传感器由一个精密的，低失调线性的霍尔传感器电路，以及一个位于管芯表面附近的铜质传导通路组成。
For the traditional reverse engineering, the tool-path is generated based on the surface fitting, surface offset and triangulation to construct the surface model.
传统逆向工程要经过曲面拟合、等距、裁剪或三角网格剖分建立其曲面模型，进而才能在曲面模型上生成数控加工刀位。
However, path mismatch such as gain mismatch, offset mismatch and clock mismatch sharply reduce the system dynamic performance.
论文首先分析了通道失配的产生原因，并且推导了各类失配对于系统动态性能的影响。
A triangular mesh surface zoning approach based on formability was given. Moreover a strategy to generate multi-stage spiral forming tool path for each surface area by offset was presented.
给出了基于可成形性的三角网格曲面分区算法和通过偏置来生成各曲面分区多道次螺旋线成形轨迹的方法。
A triangular mesh surface zoning approach based on formability was given. Moreover a strategy to generate multi-stage spiral forming tool path for each surface area by offset was presented.
给出了基于可成形性的三角网格曲面分区算法和通过偏置来生成各曲面分区多道次螺旋线成形轨迹的方法。
应用推荐