On regular highway reconnaissance work the tangent offset method is the most common one on highway route center stake layout but this method is limited because of route tangent as baseline for offset.
在公路常规勘测设计工作中，切线支距法是一种常用的中桩放样方法，但该方法以路线切线为基线，使用条件受到限制。
Center back seam with offset hem.
中心偏移下摆焊缝背面。
The system can be used to measure the offset of the beam position monitor (BPM) with respect to the magnetic center of a quadrupole.
利用该系统可以测量束流位置检测器的电中心相对相邻四极铁磁中心的位置偏移。
The pivots are located just above the center of the disc, and offset from the plane of the body seat.
枢轴就位于阀瓣中心上，偏离阀体阀座平面。
And the effect of the image distortion center bias and scale factor ratio offset on image correction quality is discussed.
并对图像的畸变中心和纵横比例因子对校正的影响做了探讨。
To solve the sphere ranging problem of fixed monocular vision, the analytical formulation of ellipse center offset is deduced, and the calibration method using this formulation is proposed.
针对球体固定单目视觉测距问题，推导了椭圆中心偏移量的解析公式，研究了基于该公式的校正方法，并进行了仿真验证。
The system can be used to measure the offset of the beam position monitor (BPM) with respect to the magnetic center of a quadrupole. Some measurement results for HLS are given.
利用该系统可以测量束流位置检测器的电中心相对相邻四极铁磁中心的位置偏移。
In this paper we also provide a formula for computing the offset caused by non-coincidence between the telescope slewing center and the dome spherical center, and make further analysis on the offset.
给出了由望远镜转动中心与圆顶球心不重合引起的偏差的计算公式，并对其进行了分析。
The hypoid gear is in common use today due mainly to the fact that the offset pinion allows the propeller shaft to be set below, (for cars) or above, (for commercial vehicles) the crown wheel center.
现在的主减速器普遍使用准双曲面圆锥齿轮，这主要是因为 主动锥齿轮的偏移允许轿车上传动轴布置得比从动锥齿轮低 一些，而商用车上又允许布置得比从动锥齿轮高一些。
The agreement is good. Finally, location offset of twist center of pile cap with asymmetrically horizontal rigidity distribution is analyzed, and some beneficial insights are provided.
最后，对刚度不对称时群桩转心位置的偏移量进行了计算分析，获得了一些有益的结论。
Through the analysis of the rotation of the wheel center round the kingpin axis, derive spindle offset and longitudinal kingpin offset algorithm;
通过分析车轮转动时轮心相对于主销轴线的运动，推导出主销横向偏移距及主销纵向偏移距的算法；
In a side view, the axis (c) of the crankshaft (28) is offset upward from the center line (a) of the cylinder.
当从侧向看时，曲轴(28)的轴线(C)从气缸的中心线(A)向上偏移。
Population gravity center and geometric gravity centre have a significant offset, and the trend of deviation from geometric gravity centre is going on.
人口分布重心向东偏离空间几何重心，且有进一步向东偏离的趋势。
Population gravity center and geometric gravity centre have a significant offset, and the trend of deviation from geometric gravity centre is going on.
人口分布重心向东偏离空间几何重心，且有进一步向东偏离的趋势。
应用推荐