The structure of hardware design is rational and reaches the demand of iris recognition.
此硬件电路结构设计合理，可以达到虹膜识别的硬件要求。
The key issues of hardware design and hex command files are explained and a demonstration is given.
对硬件电路设计和配置文件编写过程中的要点作了讨论，并给出了实例。
In this paper, method of hardware design for SPWM inverter controlled with 8098 chip-microcomputer is described.
本文介绍了一种未采用SPWM专用芯片，而采用8098单片机实现的全数字式SPWM变频器硬件设计方案。
On the base of function requirements, the paper gives a kind of hardware design of non-touched IC card charge machines.
根据功能要求，对非接触式IC卡收费机的硬件结构进行了设计。
In the part of hardware design of this paper, circuit schematic design, PCB design and system testing have been included.
本文硬件设计主要包含了电路原理图设计、系统印刷电路板设计和系统测试。
In the aspect of hardware design, the S3C44BOX development board of Samsung Company is used.
硬件设计方面，系统使用三星公司的S3C 44box开发板。
Functional verification which mostly relies on simulation is the major approach to ensuring the correctness of hardware design.
功能验证是保证设计正确性的重要手段，以模拟验证为主要方法。
In part of hardware design, voltage and current sampling circuit, IGBT driving circuit communication and man-machine interface circuit are designed.
在硬件设计中对电压、电流采样电路，IGBT驱动电路以及通讯和人机接口电路进行了设计。
In the paper the key point of hardware design and the parameter processing method were described, and the software design was also described briefly.
提出了硬件电路的设计要点及处理方法，并简要介绍了软件的设计思路。
The system is composed of hardware design of chip microprocessor, firmware design of chip microprocessor, device driver and application software design.
系统设计包括硬件设计、单片机固件设计以及设备驱动程序和用户应用程序设计。
In the aspect of hardware design, it includes video acquisition module, video processing module, wireless transmission module and Host receiving module.
在硬件设计方面，主要分为视频采集模块、视频处理模块、无线传输模块和主机接收模块四个部分。
In the section of hardware design, selection of the CAN bus communication interface card, design of CAN nodes and the signal acquisition system are introduced.
在其硬件设计中，着重介绍了CAN总线通讯接口卡的选择、CAN节点设计与信号采集系统设计。
With the automatic NC glass engraver machine, develop an open architecture NC system based on PMAC, which includes two modules of hardware design and software design.
以自动数控玻璃雕刻机为例，开发一种基于PMAC的开放式数控系统，该控制系统包括硬件设计和软件设计两大模块。
This paper probes into the application of RF technology in the wireless remote control system of electric welding machine from two aspects of hardware design and software design.
从硬件和软件设计两方面探讨了RF射频技术在电焊机无线遥控系统中的应用。
This article introduces the algorithm of DDS and the principle of hardware design in detail and gives out the circuit diagram, the principle of software design and the flow chart.
详细介绍了DDS算法和硬件设计原理，给出了电路原理图，软件设计原理及流程图。
The project of hardware design of the system is provided through the study of the characteristics of DSPs chips and the software and hardware development flow of DSP-based system.
通过对DSP芯片的特点以及DSP系统的软硬件开发流程的研究，提出了系统的硬件设计方案。
In the area of hardware design, the system uses TMS320LF2407 DSP as microprocessor, and uses intelligent power module (IPM) as inverter, which is drived by high-speed optocouplers.
在系统的硬件设计中，处理器采用TMS320LF2407数字信号处理器（DSP）；逆变器采用智能功率模块（IPM），并采用高速光耦对其驱动。
According to modularization designs for open NC system, one kind of hardware design and analysis method is introduced, which bases on DSP and CPLD to develop the motion controller.
针对开放式数控系统体系模块化设计问题，介绍了一种基于DSP和CPLD的运动控制器的硬件设计和分析方法。
According to modularization designs for open NC system, one kind of hardware design and analysis method is introduced, which bases on DSP and CPLD to develop the motion controller.
针对开放式数控系统体系模块化设计问题，介绍了一种基于DSP和CPLD的运动控制器的硬件设计和分析方法。
应用推荐