The DSP axis-angle detecting board has been proved successfully and has satisfied the requirement of numerical control machining and holds application values and excellent foreground.
本文所研制的DSP轴角检测板经试验验证基本达到了在数控加工技术中的应用要求，具有良好的实用价值和应用前景。
Some numerical examples show that the inversion results are in much good agreement with the true conductivity profile by dual induction tools measurements at the axis points.
一些数值例子表明，只利用双感应测井信号也能很好地反演出地层电导率径向剖面，且反演结果与真实电导率剖面分布吻合得相当好。
The numerical result and the critical value's effect imposed by circumferential initial stress numerical character on cylindrical thin shell beard the press at axis.
给出了周向初应力数值特征对轴向压力圆柱薄壳临界值的影响，给出数值结果。
This paper describes a computerized numerical control system for a two and a half axis upright numerical control milling machine.
讨论了一种用于两轴半立式铣床的PC -DSP主从式计算机数控系统。
The data in the center of the worksheet (tensile strength) will be plotted along the value axis (value axis: a chart axis that displays scaled numerical values.)
工作表中间的数据抗张强度沿着“数值轴”数值轴：显示刻度数值的图表坐标轴。
Through the exportation electric circuit of the exterior, the principal axis a, B, Z pulse was sent out to the measured numerical control system.
通过外部的输出电路，把产生的主轴a、B、Z脉冲发送到被测的数控系统。
A numerical computation test shows the possibility of inferring the principal axes of tectonic stress from the p, b, t axis of earthquakes with randomly oriented fault planes.
通过数值试验论证了利用多个断层面随机取向的地震的P、B、t轴推断构造应力主轴方向的可能性。
Numerical calculations were performed foran axis-asymmetric ring resonator to illustrate the application of the method.
对非轴对称环形腔作了数值计算以说明方法的应用。
Five-axis Numerical Control technology is the most difficult one among the Numerical Control technologies, and also the most widely used one.
五坐标数控技术是目前数控技术中难度最大，也是应用范围最广的技术。
The numerical simulations show that the imaging results based on AIT single frequency measurements on the axis of symmetry are in excellent agreement with the true conductivity profile.
数值计算表明，用井轴上 AIT的单频测量信号得到的成像结果与真电导率剖面分布吻合较好。
For the case that on-axis' intensity exists but the maximum intensity is not located on axis, both the LW method and GH method can be used. The two methods are compared by numerical calculations.
并使用LW法和GH法研究了轴上光强不为零但光强主极大在轴外的情况，通过定量计算对这两种方法进行了比较。
Upon the basic electromagnetic theory, wave propagation equation on an axis symmetrical case is derived. Numerical simulation method for solving the partial differential wave equation is presented.
从基本电磁理论出发，推导轴对称条件下电磁波的波动方程，给出求解此类波动方程的数值仿真方法。
The Development of the Three-Axis Numerical Control System of the Boring and Milling Machine Tool Based on IPC;
在天津大学研制的五坐标旋转锉刃磨机床的基础上，研究了旋转锉的四坐标数控刃磨技术。
The Development of the Three-Axis Numerical Control System of the Boring and Milling Machine Tool Based on IPC;
在天津大学研制的五坐标旋转锉刃磨机床的基础上，研究了旋转锉的四坐标数控刃磨技术。
应用推荐