Finally the result of the numeric simulation is provided.
并给出了数值模拟的结果。
The non-linear numeric simulation of the screw joint of SET;
最后确定装配线上的螺纹连接的转角扭矩拧紧工艺。
The nonlinear dynamic characteristics of the K set models through numeric simulation are investigated.
着重描述了K系列模型的非线性动力学特性，并通过数值模拟进行分析。
And the numeric simulation is done to get the multi-supporting results of the optical elements with large aperture.
针对各向同性圆形光学镜面做了具体的模拟计算，对圆形镜面的多点支承问题进行了初步研究。
Comparison of an actual test results with the calculation by numeric simulation from the model showed good consistence.
利用数值解法对一个测试实例进行了计算与实测的对比，结果表明有较好的一致性。
With the development of computer performance, numeric simulation method plays more and more important role in turbulence research.
随着计算机性能的不断提高，数值模拟方法在湍流研究中的重要性也在不断增强。
Finally, the remaining oil saturation distribution is predicted through numeric simulation using water displacing oil streamline simulator.
最后利用优选的地质模型通过水驱油流线模型数值模拟来预测剩余油气饱和度分布。
According to the secondary regression in quadrature combined method, the design and computation of finite element numeric simulation were done.
根据二次回归正交组合方法与油气藏射孔完井有限元模型进行了数值模拟试验的设计与计算。
The effect of field strength, initial phase, bunch shape and charge on electron beam transverse emittance is also explored by numeric simulation method.
利用数值模拟方法研究了加速场强、注入相位、束团大小、形状、电荷等因素对束流横向发射度产生的影响。
Because most of the offshore oil fields in China are in the shallow water, the experiment and numeric simulation are focused on the risers in the shallow water.
由手中国大部分的海上油田水深都比较浅，所以重点研究浅水中的海洋立管。
By the test of numeric simulation, under various exit velocities the changed rules of stress, temperature and land size about the die are analyzed in this paper.
本文利用数值模拟实验，分析了不同出口速度下的模具应力、模具温度和模具工作带尺寸的变化规律。
The result of numeric simulation of aerodynamics in the wing folding process shows that the aerodynamics at various folding velocities is approximately the same.
机翼折叠动态过程的气动特性数值模拟结果表明，不同折叠角速度下飞机的气动力相差不大。
This study has a computer aided numeric simulation of the heat and mass exchanging process in limited space on basis of the mathematical model founded previously.
对已建立的有限空间空气与水热湿交换过程的数学模型进行了计算机数值模拟。
The influence of structure factor of pressurized-swirl injector nozzle on hollow cone spray was studied by using MIXTURE dual phase flow numeric simulation method.
采用MIXTURE双相流数值模拟的方法研究压力涡流喷嘴结构因素对形成中空锥喷雾的影响。
The transient numeric simulation and relevant experiments of stator winding inter-turn short circuit fault of asynchronous motor are conducted using multi-loop mathematic model.
基于多回路数学模型，对异步电动机定子绕组匝间短路故障瞬变过程做了数字仿真，并完成了相关物理实验。
Using step surface data for wave equation simulation of seismic data can produce serious interference at corner points of steps and further affect the results of numeric simulation.
利用阶梯状地表数据对地震记录进行波动方程模拟时，在阶梯的角点处会产生严重的干扰，进而影响数值模拟结果。
The results of numeric simulation and real seismic data processing showed that the ARMA model was characterized by parameter-economic and high efficiency in comparison with MA model;
数值模拟结果和实际地震数据处理结果表明：自回归滑动平均（ARMA）模型比滑动平均（MA）模型具有参数节省、模型更为高效的特点；
It is enunciated by numeric simulation with single-chip LED. The more the temperature grade is, the more hugely the energy decreases. There is a stress concentration around the chip.
通过单芯片LED的数值模拟结果表明：温度梯度越大，能量的衰减也越大，芯片附近存在应力集中。
Adopting the numeric simulation and the numeric detection technique, the analysis and discussion is made for the eigenvector selection in the measurement of abnormal sound of bearings.
采用数字仿真和数字检测技术，对轴承异常声检测特征量的选择进行了分析讨论。
The numeric simulation of electromagnetic responses in frequency domain for electrical anisotropic formation is a challenge in current conditions of computer memory and operation speed.
在现有计算机内存和运算速度条件下，电性各向异性地层中频率域电磁响应的数值模拟是一个难点。
Moreover, it is very suitable to satellite systems equipped with on off jets and reaction wheels. Finally, numeric simulation is explored to verify the validity of pulse sequence control.
此外，由于控制输出为方波，因而适合卫星的喷气推力器控制模式和飞轮控制模式，最后通过数字仿真验证了方波序列控制的有效性。
Based on the establishment of the dynamics model of milling processes with two degrees of freedom, the end-milling processes are simulated in time domain by using numeric simulation technology.
然后以铣削为对象，建立了两自由度的铣削加工颤振动力学模型，并运用数字仿真技术，对动态端铣过程进行了时域仿真研究。
This paper puts forward a new numeric model. Simulation with actual mission data shows that the new model significantly reduces lag error and improves the accuracy of data processing.
本文提出了一种用数值法修正雷达高仰角动态滞后误差的方法，并用任务实测数据进行了模型验证，结果显示这种方法能有效地降低动态滞后引起的误差。
Numeric analysis using computer and simulation test with equivalent materials show that reinforcement of different positions of the gateway will help to control the floor heave.
计算机数值模拟及相似材料模拟试验研究表明，加固不同部位对控制底臌均有一定效果。
Numeric analysis using computer and simulation test with equivalent materials show that reinforcement of different positions of the gateway will help to control the floor heave.
计算机数值模拟及相似材料模拟试验研究表明，加固不同部位对控制底臌均有一定效果。
应用推荐