The effect of nozzle shape of seawater desalted equipment used in small ship on seawater desalination is studied.
研究了喷咀形状对小型船用海水淡化器的海水淡化影响。
The results show that the effect of the nozzle shape and the location between the nozzle and the substrate on flow field is in evidence.
数值计算结果表明，喷嘴形状及其与衬底相对位置对流场形貌有显著影响。
In this paper, the effects of nozzle shape on the properties of high pressure water jet discharging in air are investigated from theory and experiments.
本文从实验和理论两方面研究了喷嘴结构对高压水射流性能的影响。
The solutions on how to solve these problems, including fixture design, DOE based nozzle shape optimization, hot gas speed control, etc. will be introduced in this paper.
此类问题的解决方案，例如治具设计，基于DOE实验的喷嘴形状优化，热风速度控制等也将在本文中做出介绍。
It has laid the foundations for further studying the flow field in mold with mathematical models and optimizing submerged nozzle shape as well as casting process parameters.
为进一步采用数学模型研究结晶器流场、优化伸入式水口结构和工艺参数打下基础。
Because nozzle shape with oblique cut models is asymmetric, the disturbance produced at the exit of nozzle is reflected on the longer side and causes shock waves in the inner flow.
有斜切模型的喷管形状不对称，内流在出口处产生的扰动在较长一侧喷管壁反射，出现激波现象，引起流动的变化。
Finally the shape of spay was difference because of the flow conditions at the nozzle exit is not same.
由于喷嘴出口流动情况的不同造成了喷雾的形态差异。
We augment the treatment area of APCPJ by changing its shape of nozzle.
我们通过改变喷嘴的形状来增大等离子体处理面积。
The method can be used for combustion Chambers with any shape to match the fuel injection pressure, nozzle construction, injector position and intake swirl ratio with chamber shape.
该方法可适于任意形状的燃烧室，能反映出喷油压力、喷油嘴结构及安装位置、进气涡流比等参数与燃烧室形状的匹配关系。
Experiment methodology that measures the nozzle pressure of different molds has been proposed which proved that there existed the internal relationship between nozzle pressure and shape of cavity.
通过实验的方法测量出不同模具的喷嘴压力曲线，证实模腔几何形状与喷嘴压力之间存在确定的关系。
A kind of conformal design scheme for tailpipe nozzle and inlet cowl was put forward, which not only keeps missile shape, but also realizes integral conformal design with inner contour of nozzle.
提出了一种尾喷管与进气道整流罩保形设计方案，既保持导弹外形特征不变，又与尾喷管内型面实现一体化保形设计。
It also studies the effect of nozzle, orifice shape and the amount of dissolved gas on the spray quality and configuration.
喷嘴喷孔形状和溶气量对喷雾质量、结构的影响。
The results show that the effect factors of EMBr are slab width, casting speed, the shape of submerged entry nozzle and so on.
结果表明，电磁制动的影响因素有板坯宽度、浇注速度、浸入式水口的形状等。
The results show that the effect factors of EMBr are slab width, casting speed, the shape of submerged entry nozzle (SEN) and so on.
结果表明电磁制动的影响因素有板坯宽度、浇注速度、浸入式水口(SEN)的形状等。
The results show that the rate of the growth of each point on the surface crack is connected with the place of crack and the structure of nozzle, and its steady shape is some of complex curve.
结果表明：表面裂纹各点的扩展速度与其所处的位置和容器接管的几何参数有关，且其扩展平衡状态为一不规则形状。
Glass coaters graphite nozzle (SDXL), graphite fork, graphite set wire wheel, Abnormal shape graphite pieces. etc.
玻璃镀膜机石墨喷嘴(加长型)，石墨拨叉、石墨集丝轮，异型石墨件等。
Shape selection and dimension optimization of direct jet high pressure spray nozzle were done.
对直射式雾化喷嘴进行选型及内部尺寸寻优。
The nozzle vane is difficult to be cast due to its large size and complicated shape.
由于该叶片尺寸大、形状复杂，给铸造工艺带来很大难度。
Selective soldering can be done under an Angle (tilt) like in wave soldering or horizontal with different shape of nozzles and nozzle materials.
选择性焊接可以完成倾斜式波峰焊接或使用不同的喷嘴形状与材料的水平式焊接。
DPSZ type hot nozzle, suitable for all kinds of product, it shows point shape when entering the gate, there is a circle on the surface of the product, easy to change the color.
点浇口热嘴，适用于各种塑料，进浇点呈点状，产品表面有一个圆，换色性能佳。
There are many kinds of nozzles, among which the needle-shape nozzle is widely used in practice.
喷嘴的型式很多，目前使用最广泛的是针型喷嘴。
There are many kinds of nozzles, among which the needle-shape nozzle is widely used in practice.
喷嘴的型式很多，目前使用最广泛的是针型喷嘴。
应用推荐