The optimal distribution is made possible by an electronically controlled hydraulic system in the multi-gear clutch.
这种最佳扭矩分配是由多片离合器中的一个电控液压系统实现的。
Secondly, analyzing statics characteristic of the multi-gear pump demonstrates that radial hydraulic pressure, meshing force and resultant force are balanced on the center wheel.
其次，对多齿轮泵的静力学特性作了分析，证明了中心轮径向液压力、啮合力及总作用力平衡。
This paper analyzed the system output response dynamic characteristics of spinning gear adjustment control system of multi-point forming press.
以多点成形压力机中多轴齿轮传动调形单元为例，研究了传动系统输出响应的动态特性。
This paper discusses the assembly drawing of series products as an example of the gear transmission of the multi-spindle head.
本文以多轴钻孔组合机床传动箱为实例，对系列产品装配图自动绘制的方法作了探讨。
Based on the method of non-contact pick-off detection of gear tooth, the detection system of a radial multi - gear flow was designed.
基于非接触式齿轮速度传感器检测原理，设计了一种径向多齿轮流量变送器测量系统。
CAM system based on industry computer and multi-task motion controller adopts the electrical gear to accomplish synchronous motion control of the winding machine.
基于工控机和多任务运动控制器的缠绕机CAM系统采用电子齿轮方式实现缠绕机同步运动控制。
Based on multi-parameter, multi-objective and multi-constraint of helical gear reducer, the optimization mathematical model was established.
针对斜齿轮减速器优化设计的多参数、多目标、多约束特点，建立了多目标优化数学模型；
With the help of ANSYS system, it mainly deals with the modeling of a multi-stage gear rotor system with finite element method and analyzing the vibration modes of the system.
利用有限元应用软件ANSYS建立了齿轮转子系统耦合振动分析的有限元计算模型。
This essay describes the application of the cylinder cram mechanism and the planetary gear system in the multi head anti stealing cover seal mechanism.
通过行星轮系-圆柱凸轮机构在多头防盗盖封口机中的应用，详细论述了其运动原理及设计要点。
Based on the model of multi-span slender rod, the moment equations and deflection equations of elevator rail with duplex safety gear were established and resolved in a complex state of stress.
结合双安全钳作用特点，以多跨度细长杆模型为基础，建立并求解了电梯导轨在复杂受力状态下的弯矩方程和挠曲线方程。
As a result, it is necessary to research how spherical gear mechanism be utilized with flexible multi-link manipulator.
因而研究将球齿轮机构用于柔性多关节机械手很有必要。
The single stage skewed tooth cylindrical gears reduction gear optimized design, is a multi-objective optimization question.
单级斜齿圆柱齿轮减速器的优化设计，是一个多目标优化问题。
This paper presents the method of multi information acquirement and the theory of multi parameter testing in intelligent analyzing station for gear drive system.
本文论述了齿轮传动系统智能分析站中复合信息的获取方法及动态参数的测试原理。
Regarding the "balancing" problem which arose in the automobile gear manufacturing enterprise, some research on the multi-layer planning method in the manufacturing process is done.
结合汽车齿轮制造企业在生产过程中物流的“均衡性”问题，研究了产品制造流程分层次规划方法。
More and more planetary gear mechanisms are being used in HEV as multi-power coupling mechanism because of their compact structure, high transmission efficiency and strong load bearing capacity.
行星齿轮机构因其结构紧凑、传动比大和承载能力强等优点被越来越多地作为多能源动力耦合机构，应用于混合动力汽车中。
The results show that response frequency of gear mechanism will be reduced by gear backlash and multi-frequency phenomenon will occur.
计算结果表明，齿侧间隙的存在会降低机构的响应频率，并会产生多频现象。
The system uses ultrasonic wave as signal source, with the multi-probe multi-directions sweep, and fluid soak method test the gear.
系统以超声波作为检测信号源，采用多探头多方位扫描、液浸法的方式对齿轮进行检测。
The Main Landing Gear wheels have multi-disc carbon brakes using Green hydraulic pressure for normal operation and Yellow hydraulic pressure through an alternate braking system.
主起落架机轮使用多盘碳刹车，正常情况使用绿色液压系统，备用刹车使用黄色液压系统。
Suitable position of gear engaging point is confirmed by analyse forces on the BFP improve type flexible driving with multi-channel engaging.
通过分析BFP改进型多柔传动 装置受力，确定齿轮啮合点的适当位置。
The design of an internal toothing gear shaping cutter can be summed up to a multi-target optimization problem. A mathematic model for optimization is established.
把内齿轮插齿刀的设计归结为一个多目标的优化问题，建立了优化的数学模型。
The input shaft is connected to the ring gear (blue); The output shaft is connected to the planet carrier (Green) which is also connected to a "multi-disk" clutch pack.
输入轴与齿圈（蓝色）连接，输出轴与行星架（绿色）相连，行星架上装有多片离合器。
Multi-purpose mini-motorcycle in the belt drive gear for the latter, the main, the size of the driven pulley reduction ratio sub-decision.
在微型摩托车多用皮带传动方式作后传动装置，主、从动皮带轮的大小决定次级减速比。
The heat-treat technology is an essential one in the gear processing industry, and multi-purpose is optimal for heat-treat technology.
热处理工艺是齿轮加工行业中必不可少的工艺。
The optimal design of a six-bar linkage to be used in the main driving mechanism of a gear planer is discussed and treated as a multi-objective problem.
本文首先讨论了在插齿机主传动机构中使用的六杆机构的优化设计问题，并建立了一个多目标数学模型。
Multi gears is commonly used for the winch of oil RIGS each with different gear changing method.
石油钻机的绞车一般设计成多个档位，各档的挂合和变更方法都不同。
Based on the theory of workflow management system, the multi-degree-of-freedom dynamics analysis and management platform of gear transmission system has been established.
基于工作流管理系统的理论基础，建立了齿轮传动系统的多自由度动力学分析管理平台。
This machine is equipped with a gear transmission mechanism, and its multi-dies are arranged in line. It can draw steel, aluminum, brass and other kinds of metal wires.
本机采用齿轮变速传动结构，串联组成多模连续拉丝机，可拉拔钢、铝或黄铜等金属线材。
In this thesis, planar double-enveloping worm gear pairs is the research object, combined with space Meshing theory, derived from the multi-parameter modification of the mesh equation.
本文以斜平面二次包络环面蜗杆副为研究对象，在空间啮合理论的基础上，推论出三参数修正的啮合方程、接触线方程、蜗轮齿面方程。
This dissertation primarily represents the study of in multi-degree-of-freedom system dynamics and structural dynamics analyses of an aeronautic gear transmission.
本文主要在齿轮传动系统的多自由度系统动力学及其主要传动件结构动力分析两个方面进行了论述和研究。
This machine is equipped with a gear transmission mechanism, and its multi-dies are arranged in line.
本机采用齿轮变速传动结构，串联组成多模连续拉丝机。
应用推荐