A twin monostable circuIt 'supplies the data and strobe signals.
两个单稳态电路提供数据和滤波信号。
This paper brings forward a method of threshold processing PWM signals duty cycle by employing monostable multivibrator.
提出了采用单稳态触发器对采集的PW M波形进行占空比门限处理的方法。
The switch circuit is composed of an emitter-coupled trigger circuit, an integral delay circuit and a monostable circuit.
其中开关电路由射极耦合触发电器、积分延时电路、单稳态电路三单元构成。
The accuracy of delay or timing is not sensitive with monostable trigger circuit since electrical elements have influence on it.
使用单稳态触发电路作“延时”或“定时”用，由于受到元件和器件的影响，其精度不会太高。
Based on the monostable circuit, using the IC NE555, a kind of hot water circulation automatic heat preservation system was designed.
利用时基icNE555接成的单稳态电路，设计了一种热水循环自动保温系统。
The digital realization of monostable circuit and extraction of bit-synchronous signal with digital phase lock loop are also introduced in detail.
对于其中的单稳态电路的数字化和数字锁相环提取位同步信号也进行了详细的设计说明。
The synchronous signal of MC1311 CMOS camera is shaped by monostable trigger 74ls221. The data are stored in AT24C02, protected in the case of electricity loss.
使用单稳态触发器74ls221对送给MC 1311CMOS摄像机的同步信号进行整形。使用AT 24 C02对数据进行存储，实现了数据的掉电保护。
Secondly we changed the sampling mode, using dual monostable multivibrators to select the focusing window, which solves the sampling drift problem raised by SCM break.
其次改变了系统的采样方式，采用双单稳态出发电路对调焦窗口进行选择，解决了原来存在的因中断产生的采样漂移问题。
A tester is made based on the typical circuit of the monostable trigger made of 555 timers. It operation principle, coupling way and usage are analysed in great detail.
以555定时器构成的单稳态触发器这一典型电路为基础自制一种实用测试器，较详细的分析了该器件的工作原理、耦合方式、使用方法。
According to characteristic of computer control system of electrohydraulic motion platform, the paper designs a surveillance protection system by the monostable trigger.
以单稳态触发器为核心，针对电液运动平台计算机控制系统的特点，设计了电液运动平台的监控保护系统。
It is found that the system will be in monostable state or bistable state, which is controlled by the competition between the uniaxial anisotropy and the exchange anisotropy of the system.
交换各向异性与单轴各向异性之间的竞争使体系存在单稳态与双稳态两种不同的状态，直接决定了交换偏置的角度依赖关系。
The 13.31 is a simple monostable relay with screw terminals suitable for interfacing applications where the coil is low-voltage (e. g. 24 v) and load is at the supply network voltage (230 v).
31是一个简单的螺丝端子适用于接口应用线圈低压单稳态继电器(24V)和负荷在供电网络的电压(230 V)。
The 13.31 is a simple monostable relay with screw terminals suitable for interfacing applications where the coil is low-voltage (e. g. 24 v) and load is at the supply network voltage (230 v).
31是一个简单的螺丝端子适用于接口应用线圈低压单稳态继电器(24V)和负荷在供电网络的电压(230 V)。
应用推荐