The most important grinding variables from the point of view of wear are feed size, grinding media size, mill speed, and mill diameter.
就磨损观点来看，橡胶衬板最重要的磨损因素是给矿粒度，磨矿介质尺寸，磨机转速和简体直径。
After preparing carefully, the former discharging method is remaked and the mill speed is greatly improved with the better economic benefit.
工艺、设备人员经过周密准备，将再加热炉原有出料方式进行了改造，大幅度提高了轧制节奏，取得了良好的经济效益。
Functions of the device include the measurement of strip tension and mill speed as well as adjustment of flanging the rolled piece with respect to the roll during"S"roiling.
该设备能用来测量轧制过程带材的张力和速度，还能用其实现“S”方式轧制时对轧辊的包角调整。
This paper presents the application of speed and tension control system in the line of universal mill of Anshan Rolling Steel Plant.
本文介绍了速度及张力控制系统在鞍山市轧钢厂万能轧机轧制线上的应用。
Investigates a method for increasing the positioning accuracy of electric APC (auto position control) system for plate mill while assuring its positioning speed.
研究在保证中板轧机电动APC(自动位置控制)系统定位速度的同时提高定位精度的方法。
A new approach to master speed control is proposed, in which coil box and roughing mill and finishing mil are combined with each other as master-slave device.
提出了一种热卷箱与粗轧和精轧互为主从的主令速度控制新方法。
This paper describes the coilbox speed control and speed matching of coilbox and rougher, finishing mill, delivery table etc.
介绍了热连轧机中热卷箱的速度控制及其与轧机和辊道的速度匹配关系。
The advanced development process flow of "converter-small billet continuous casting machine-high speed wire rod mill" is adopted in developing EH14 wire rod for weld.
青钢应用“转炉-小方坯连铸机-高速线材轧机”工艺流程试制EH14焊接用钢盘条。
The methods of powder surface modification in existence are done in reaction kettle, blend machine, high speed mill, high speed crumb, liquid state jet mill etc.
现有粉体表面改性方法的具体实施是在反应釜、混合机、高速搅拌机、高速捏合机、液态流化床和高能磨中进行。
A brief introduction is made on the configuration, equipment level and test run of high-speed newsprint machine (PM5) in Nanping Paper Mill.
简要介绍福建省南纸股份有限公司高速新闻纸机(PM 5)的选型过程、装备水平以及试生产情况。
Some negligence in design about discharge method of reheating furnace limit the speed and the output of PQF mill line.
由于再加热炉出料方式设计上的原因，限制了PQF轧机生产线的轧制节奏，从而影响产量。
Approximation of screwdown value, rolling speed and an iterative method were used to study the maximum screwdown ratio, speed, tension and deformation ratio tolerable in the mill.
作者用压下逼近法、速度逼近法及迭代法研究了该轧机允许的最大压下率、速度、张力和变形率。
The method and example of pass optimization design of high speed wire rod finishing mill by dynamic programming with minimum total tension coefficient are described.
阐述了以动态规划法按最小总张力系数对高速线材轧机精轧机组孔型进行优化设计的方法与实例。
For the sudden fault of transmission parts in high speed wire rolling mill, the fault diagnosis based on the vibration measurement is an effective method.
针对高速线材轧机传动零部件的突发故障，开展基于振动测试的故障诊断研究可以有效加以避免。
The technology design and its characteristics of a single stand high speed wire rolling mill building in Xiangtan Iron & Steel Co. were introduced.
简要介绍了湘钢华光线材有限公司建设的一套单线高速线材轧机的工艺设计及其特点。
The technology, equipment and technical parameters of high speed wire-rod mill in Zhangjiagang, with the highest technical level in the world, are introduced.
介绍了具有当前世界线材轧机最高水平的张家港高速线材轧机的工艺、设备情况及主要技术参数；
The principle of minimum tension control in high - speed wire rod rolling mill and the concerned calculation are introduced in this paper.
文章主要介绍了高速线材轧机的微张力控制原理，并对算法实现进行了详细描述。
The screwdown block is improved by mechanics analysis with boundary element method, and a simple device is designed for dynamic load of oil film bearing used in high-speed wire rolling mill.
通过采用边界元法对高线轧机压下垫块改造模型进行力学分析，开发设计一种适合测量高线轧机油膜轴承动态载荷特性的简易装置。
The flow fields in the HP medium speed mill were simulated by employing the numerical simulation meth-od.
利用数值模拟法对中速磨煤机内的一次风流场进行了模拟。
With the improvement of unit load and parameters of the power plant, coal-fired power plant USES medium speed mill direct-firing pulverizing system in common.
随着火电机组容量和参数的不断提高，火电厂普遍采用中速磨直吹式制粉系统。
In high speed wire-rod mill, guide roller is the main consumption tool, excellent wear resistance, adhering steel resistance and hot fatigue resistance are required.
导辊是高速线材轧机上的主要消耗工具，要求高耐磨性、抗粘钢性和热疲劳抗力。
But it has not been long to use the middle-speed mill and fan mill in thermoelectric generator units in China, and there are still big gaps between the simulation model and the actual behavior.
而我国火电机组采用中速磨煤机和风扇磨煤机的历史不长，对其制粉系统的运行特性建立的仿真模型与实际运行工况还存在不小的差距。
To introduce the trial production process of ML08Al cold heading steel adopting the process of converter steel-making, LF refining, billet continuous cast and high speed wire rod mill.
介绍采用转炉、l F炉精炼、小方坯连铸机、高速线材轧机生产工艺试制ML 08 A l冷镦钢的过程。
The ball mill′s rotational speed can only affect the impact force and frequency and has no influence on its separation point between balls and mill wall.
高能球磨机的转速不会影响磨球与磨筒壁的脱离点，只会影响磨球对粉体的撞击力及撞击频率。
The rolling pressure on high speed untwist wire rod mill was measured firstly and succeeded internationally for optimizing technology, pass design, and management of the plant.
首次对高速无扭线材轧机粗轧机组压力进行测试并取得成功，为优化工艺规程、优化孔型设计及设备全过程的经济管理与改进提供了可靠的依据。
The requirements for a computer control system used for a rolling mill, especially for hot strip mill, are the high speed control cycle and high speed communication between controllers.
轧钢自动化，特别是带钢热连轧自动化，要求计算机控制系统具有高速控制、高速通信能力。
In view of low milling efficiency, the effect of milling form, loading coefficient of materials, rotational speed of ball mill, milling time and grinding aid on milling efficiency was discussed.
针对陶瓷生产中球磨机效率低的问题，从工艺上讨论了研磨方式、物料的装填系数、球磨机转速、研磨时间以及助磨剂对球磨机效率的影响。
In view of low milling efficiency, the effect of milling form, loading coefficient of materials, rotational speed of ball mill, milling time and grinding aid on milling efficiency was discussed.
针对陶瓷生产中球磨机效率低的问题，从工艺上讨论了研磨方式、物料的装填系数、球磨机转速、研磨时间以及助磨剂对球磨机效率的影响。
应用推荐