Based on a viscosity amendment model of gas flow in micro-gap, squeezs gas film damping effect on micro plates is investigated.
基于微缝隙气流的粘度修正模型，分析了气体对微圆盘的压膜阻尼效应，得到微圆盘表面的压强分布、压膜阻尼力和压膜阻尼系数的解析解。
For high ozone content and efficiency, the discharging behavior and performance of a plate-type micro-gap ozone generator were studied.
以获得高效率高浓度臭氧为目标，研究了平板式微间隙臭氧发生器的放电特点和性能。
Wong’s frequent updates to her micro-blog bridges the gap with the public, showing her approachable self.
王菲经常会更新微博，拉近与公众的距离，这也展现出她平易近人的一面。
The electrolytic products are hard to be removed from the small machining gap in micro ECM(electrochemical machining) process, which decrease the machining efficiency, stability and quality.
微细电解加工时，由于间隙微小，生成的电解产物因难以从加工区域中移除而降低了加工速度甚至中断加工。
Thus, a zero gap is realized, where no gap between micro lenses exists, and the fill factor of micro lens is maximized.
因此，实现了零间隙，即，在微透镜之间不存在 间隙，微透镜的填充系数被最大化。
The electrolytic products are hard to be removed from machining gap in micro-ECM (electrochemical machining) process, which may lower machining speed or stop the machining process.
微细电解加工时，由于间隙微小，生成的电解产物因难以从加工区域中移除而降低了加工速度甚至中断加工。
The electrolytic products are hard to be removed from the small machining gap in micro ECM(electrochemical machining) process, which decrease the machining efficiency, stability and quality.
微细电解加工时，微小加工间隙内的电解产物难以移除，会降低加工效率、影响加工稳定性和质量。
The relation between the air gap thickness and the peak wavelength in micro-optical electromechanical system (MOEMS) optical tunable filter based on Fabry-Perot etalon is discussed.
分析了基于法布里珀罗腔的微光机电系统可调谐滤波器中，空气腔厚度与峰值波长间的关系。
Further along, the influence of harmonic wave of magnetic conductivity of air gap and saturation of motor on wave pattern of wind electric current of micro-step driving was analyzed.
进而分析了气隙磁导谐波及电机饱和对微步驱动电流波形的影响。
The discovery has filled the gap in the studies of the Permian system occurring in micro-landmass and is significant to the researches of numerous oceanic islands in the ancient Tethyan.
该套地层的发现填补了微陆块上二叠系地层的空白，对古特提·斯多岛洋研究具有重要意义。
The electrolytic products are hard to be removed from machining gap in micro-ECM(electrochemical machining) process, which may lower machining speed or stop the machining process.
微细电解加工时，微小加工间隙内的电解产物难以移除，会降低加工效率、影响加工稳定性和质量。
The electrolytic products are hard to be removed from machining gap in micro-ECM(electrochemical machining) process, which may lower machining speed or stop the machining process.
微细电解加工时，微小加工间隙内的电解产物难以移除，会降低加工效率、影响加工稳定性和质量。
应用推荐