He was unconscious for several weeks and woke up with a metal plate in his head.
有好几个星期他都神志不清，等他醒来的时候，脑袋里已经被装了块金属板。
A mass of wires spills out of a wooden box; on top sits a metal plate punched full of holes.
一大团电线耷拉到了一个木箱子外面；一个打满孔的金属盘放在木箱上面。
This metal plate is exposed to light and creates an image which is then transferred to paper.
这种金属板在曝光后可以产生能被转移到纸上的图像。
To perform this test, you need a fixture that positions a metal plate over the circuit under test.
为了完成这项测试，你需要将一个金属板放置到被测电路的上面。
Stone, and later metal plate, was used as the image carrier, in which the image areas and non-image areas were defined chemically.
最初用石块作印版，后来才改用金属版。版面的印纹和非印纹用化学方法界定。
Historically, wafers were waxed onto a metal plate.
过去片子是用石蜡固定到金属板上。
The trademark is embossed on a metal plate inside the headboard.
商标凸印在床头板内侧的金属牌上。
The metal plate used to fasten an add-in card to the system chassis.
用来把插卡固定到系统机箱上的金属板。
The wave charts of laser ultrasonic pulse and its echoes in metal plate are shown.
文中给出了激光超声脉冲及其在金属板中的回波的波形曲线；
These electrons will not pass into the phototube because of the insulation on the metal plate.
由于金属板上有绝缘层，这些电子不能进入光电管。
The efficiency of laser-drilling a metal plate in water was observed higher than that in air.
在其它条件相同的情况下，水中激光在金属薄片上的打孔效率远高于空气中的打孔效率。
And I began to learn to use computer and metal plate drawing software under the influence of designers.
我则在设计员的影响下开始学用电脑和钣金绘图软件。
Super thermostatic water bath shell made of metal plate, a control box is mounted directly on the water tank.
超级恒温水浴外壳采用金属板，控制箱直接安装在水箱上。
The process of preparing a printing surface for electrotyping by first engraving on a wax-coated metal plate.
蜡模，蜡刻制版法：一种通过先在涂蜡金属板上刻字来准备电版印刷平面的工序。
By measurement of the scanning Angle of the laser beam, the displacement of the metal plate can be calculated.
通过对光束扫描角度的测量，就可计算出金属板的位移量。
Results: Data of upper edentulous jaw models and a palatal metal plate of upper complete denture were obtained.
结果：获得无牙颌三维数据及上颌金属基托的数据文件。
The surgeon places the graft into the open space in your spine. It may be secrured with a metal plate and screws.
术者将植骨块放入脊柱减压的空隙，并用金属接骨板和螺钉对其进行固定。
That will include more practical alternatives to the metal plate, perhaps delivering energy via a patch on the skin.
他们还想到了许多方案来替代金属薄片，比如说通过在皮肤上的一块补丁来传输能量。
In practice, the shearing and punching process is often used to cut the metal plate into finished items in two stages.
生产中常采用剪冲下料工艺分两阶段将金属板材分割成毛坯。
The output and quality of metal plate and strip are heavily affected by electromechanical vibration in rolling process.
轧钢过程中的负荷扰动容易激起机电振动，这严重影响板带材的产量和质量。
Thickness gauges are mainly used for measuring thickness of paper, leather, rubber, fabric, metal plate and glass, etc.
测厚规主要用于测量纸张、皮革、橡胶、织物及金属板材、玻璃等的厚度。
The output and quality of metal plate and strip are heavily affected by performance of the main drive system of rolling mill.
轧机主传动系统通常由直流电机驱动，其性能好坏直接影响板带材的产量和质量。
This paper introduced the method of clinching to achieve the connection of metal plate and an analysis was made on forming principle.
本文介绍了压印连接方法实现金属板件连接的新技术，分析了压印连接的成形原理。
In the process of metal plate, the laser cutting process can not only save the cost of die, but also can shorten the processing cycle.
就加工金属板材而言，采用激光切割加工工艺不仅可以节约昂贵的模具费用，而且可以缩短加工周期。
The dial thickness gauges are used to measure the thickness of paper, leather, rubber fabric, metal plate, glass and plastic plate, etc.
测厚规主要用于测量纸张、皮革、橡胶、织物及各种金属板材、塑料板等的厚度。
The dial thickness gauges are used to measure the thickness of paper, leather, rubber fabric, metal plate, glass and plastic plate, etc.
用途used测厚规主要用于测量纸张、皮革、橡胶、织物及各种金属板材、塑料板等的厚度。
Artistic express-a variety of materials and colors is available for the exterior metal plate, and various complex curving surfaces can be provided.
艺术表现力——外层金属板可选择多种材料和颜色，并可形成各种复杂空间曲面。
The article introduces property and installation of new motor general protector with electronic re - lay substituting for double metal plate relay.
介绍以电子式热继电器取代双金属片式热继电器的新型电动机综合保护器的性能特点以及安装接线方法。
This paper suggests a method for measuring the thickness of metal plate for working pieces on line using the eddy current sensors without any damage.
提出一种用电涡流传感器实现无损在线测量工件金属膜厚度的方法。
As by the two sides of the diaphragm metal plate is placed, changes of gap caused by deformation of diaphragm lead to changes of capacitance accordingly.
膜片两侧置有金属板，膜片变形引起的间隔变化将使电容之发生变化。
应用推荐