PBS has excellent mechanical properties and can be applied to a range of end applications via conventional melt processing techniques.
PBS的具有优良的机械性能，可应用于传统的通过结束熔融加工技术的应用范围。
PHB copolymers are preferred for general purposes as the degradation rate of PHB homopolymer is high at its normal melt processing temperature.
基丁酸酯共聚物是作为均聚物PHB的降解率一般用途的首选是在其正常高熔体加工温度。
However, the polymers are less pseudoplastic than LDPE, so melt viscosities are higher during processing.
然而，此聚合物的假塑性不如低密度聚乙烯好，因此在加工时的熔体粘度较高。
The inclusion removal efficiency for the continuous processing of aluminium melt with the high frequency magnetic field is analyzed in the thesis.
分析了高频磁场作用下铝熔体连续处理时夹杂的去除效率。
By using melt gear pump, production efficiency and product quality can be improved and production cost can be reduced in the polymer processing.
在聚合物加工中使用熔体齿轮泵可以提高生产效率和产品质量，降低生产成本。
Highly toughened, heat stabilized polyamide 612 for extrusion, blow molding or processing by other techniques requiring high melt viscosity.
高增韧，热稳定挤出，吹塑或处理聚酰胺612熔体粘度高，要求其他技术。
Based on experiment and data calculation, this viscosity model could sensitively and quantitatively reflect the impact of the processing parameters on the apparent viscosity of the melt.
依靠实验及数据计算，检验此模型能够灵敏地定量反映外部加工条件对熔体表观粘度的影响。
A thermoplastic polyester elastomer designed for blow molding or processing techniques requiring high melt viscosity.
聚酯弹性体设计用于吹塑或处理技术要求高熔体粘度。
Moreover, by using a new kind of processing technology-the electro magnetic dynamic extrusion technology, the polymer melt strength can be reinforced.
同时提出了一种新型的加工技术，电磁动态挤出成型技术可以有效地提高聚合物熔体的强度。
The influences of processing parameters, material properties and screw design on melt temperature distribution in reservior during injection moulding are described in this paper.
本文叙述了注射成型中加工参数、物料性能及螺杆结构对存料区熔体温度分布的影响。
The performance and feature of melt gear pump in the polymer processing was introduced, and the purpose and characteristic of melt gear pump for plastic and rubber extrusion was listed.
介绍了熔体齿轮泵在聚合物加工中的性能与特点，列举了用于塑料、橡胶挤出的熔体齿轮泵的用途和特点。
The influences of the different contents of CPE on melt rheological property of processing modified RPVC, dynamic and static heat stability and mechanical property were discussed mainly.
主要探讨不同用量的CPE对改性硬质pvc的加工熔体流变性，动、静态热稳定性及物理力学性能上的差别。
For these low melting point polyesters with different content of modifier r, the influence of temperature on viscosity of melt must be paid attention during post processing.
对于改性剂r含量不同的低熔点聚酯，在后加工时应充分考虑到温度对熔体粘度的影响。
In this work, we researched extrusion processing technology of PFSIEMs, including melt-extrusion and gel-extrusion.
本工作研究了PFSIEM挤出加工技术：熔融挤出法和凝胶挤出法。
The results showed that the processing history had a great influence on the crystallization and melt behavior of nylons.
结果表明，加工历史对尼龙的结晶和熔融行为影响很大。
This may be the reference for the processing of decarbonization of low-carbon ferrochromium melt in vacuum.
对微碳铬铁熔体真空脱碳处理有一定参考意义。
Meanwhile, binary processing aid also showed effect on increasing the critical shear rate for the onset of sharkskin melt fracture.
同时复合加工助剂对改善鲨鱼皮熔体破裂也有一定的作用。
The processing mechanism of electric melt explosion and eclipse divided by metals are analyzed in this paper.
对电熔爆加工原理及加工蚀除金属的机理进行了分析。
A thermoplastic polyester elastomer designed for blow molding or processing techniques requiring high melt viscosity.
热塑性聚酯弹性体设计用于吹塑或处理技术要求高熔体粘度。
Two is due to the hot melt connection is the plastic pipe of the two processing, make high quality plastic into recycled plastic, connection reliability.
二是由于热熔连接是对塑料管的二次加工，使得优质塑料变成回用塑料，连接的可靠性降低。
Formulated for superior surface aesthetics, it exhibits excellent melt stability and high flow over a broad range of processing conditions.
优越的表面美学的配方，它具有优良的熔体稳定性和加工条件的范围广泛的高流量。
The processing property show low intensity, low recovery, extremely grind, weak slag bonding, high heat stability, high melt ash content and middle dressing.
具有低强度、低还原率、极易磨、弱结渣、高热稳定性、高熔灰分、中等可选的工艺性能。
This essay described the FEM simulation of plastic pipe extrusion: the factors of melt line formation and heat transfer of cooling processing were mainly discussed.
本文利用有限元法对塑料管材的挤出进行模拟。主要讨论了影响塑料管材挤熔接痕形成的因素，以及管子冷却过程的热传递。
Nevertheless foaming processing of PP is very difficult because of its high crystallinity and poor melt strength.
但由于PP的高结晶性，熔体强度低，其发泡成型较为困难。
The high melt strength and heat stability of these resins permit the use of relatively large die openings and high-temperature draw-down techniques, which increase processing rates.
高熔体强度和热稳定性允许这些树脂较大的模具开口和高温画式的技术，从而增加处理速度使用。
A model on Melt - spinning dynamics of spandex is established, and its processing is studied by the way of analogue computation.
建立了弹性纤维熔融纺丝的动力学模型，并利用计算机模拟探讨了其纺丝动力学过程。
The processing parameters of PEEK composites include cooling rate, forming pressure, forming temperature and the holding time in melt.
其成型工艺参数包括冷却速度、成型压力、成型温度、保温时间。
The processing features of parallel spinning and the design of conjugated spinning beam with double shield melt canal are introduced in detail.
详细说明平行纺丝的工艺特点和双护套熔体通道的复合箱体设计。
The results show that, after laser surface processing, a melt layer with cellular-dendrite structure is formed, which could transform into very fine-grained structure during the annealing treatment.
结果表明，激光处理后试样表面熔凝区的组织主要为胞状枝晶组织，经后续热处理可转变为细小的等轴晶粒组织，并形成了良好的超塑连接条件。
The results show that, after laser surface processing, a melt layer with cellular-dendrite structure is formed, which could transform into very fine-grained structure during the annealing treatment.
结果表明，激光处理后试样表面熔凝区的组织主要为胞状枝晶组织，经后续热处理可转变为细小的等轴晶粒组织，并形成了良好的超塑连接条件。
应用推荐