In high voltage power system, in order to raise measurement accuracy, errors must be reduced.
在高压电力系统中，为了提高电压互感器的测量准确度，必须减小误差。
This paper discusses the errors in verification system of small volume measurement instrument, and gives a detailed analysis on the test ways of small capacity measuring instruments.
本文论述了小容量计量器具检定系统存在的误差问题，并详细的分析了小容量计量器具的验定方式。
In test and measurement system, if the dynamic characteristic of sensors can not meet the requirement, sensors will cause dynamic errors.
在测试系统中，若传感器的动态特性不能达到系统的要求，测量系统就会出现误差。
Based on the attributes of different errors, the method for transferring miss distance measurement error in servo control system is given.
在考虑不同误差属性的基础上，给出了脱靶量测量误差在伺服控制系统中的传递方法。
This paper describes a method for the homogeneity measurement of optical material which is free from the system errors and the sample geometrical errors.
本文叙述了一种不受干涉仪系统误差及试样加工误差限制的测试光学材料均匀性的方法。
A modified phase shifting algorithm is used in our testing system to improve the measurement accuracy, which decreases the errors from phase shifter and detector's nonlinearity.
系统采用了改进的相移算法，抑制了相移器误差以及探测器带来的非线性误差，提高了测量精度。
The paper presents a method of achieving accuracy loss of the dynamic measurement system according to change of errors on different period of the system.
文中提出了利用动态测量系统在不同测量时期的误差量值变化来获得系统的损失精度的方法。
It is proved that the field application of cooling water recirculation system can meet the measurement standards and reduce metering errors.
通过冷却循环水系统的现场应用，达到了计量标准的要求，降低了计量误差，验证了该系统在原油计量中的作用。
This paper analyses the error factors that affect the measurement accuracy in high precision photoelectric camera system, and presents errors calibration method in detail.
详细分析了影响高精度光电摄像系统测量精度的各项误差因素，针对这些误差因素提出了详尽的标定算法，建立了摄像系统的标定模型。
Nonlinear errors caused by mis-installation of common-path heterodyne interferometer affected the measurement precision of the system.
共光路外差干涉仪具有很高的分辨率，但因为安装、调试误差会产生非线性误差，影响系统的测量精度。
Theoretical analyses and simulated experiments show that this measurement control system can effectively control the errors caused by the disturbance-accelerated speed.
理论分析和模拟实验结果表明，该测量装置能有效抑制干扰加速度造成的测量误差。
Therefore, the study of fault detection and error analysis for the measurement and testing system is to effectively reduce faults and errors on the impact of the test results.
因此，研究测量及测试系统的故障检测与误差分析，以有效减少故障和误差对测试结果的影响，提高测试精度成为必需。
Presents the composition, the principle and measurement methods of a non-contact automatic system for measuring shape and position errors of revolving body in high temperature.
介绍一种新研制的高温回转体零件形位误差综合自动测量系统的构成、检测原理和方法。
Flexible coordinate system is introduced into theodolite industrial measurement, so there arent errors of instruments levelling and relative orientation in self locating of the system.
将柔性坐标系引入经纬仪工业测量中，使其系统自定位不再受仪器整平误差和相对定向误差的影响。
The errors in the Marine magnetic gradient measurement are divided into system noise, heading errors, geometrical effects, swell noise and sensor motion.
将影响梯度测量的误差主要分为四种：系统误差、航向磁效应、几何效应、波浪噪声及传感器运动误差。
The effects of main errors of the system on the measurement results were analyzed, and some experiments were performed to extract and calculate the main errors of this system.
分析了系统的主要误差对测量结果的影响，完成了主要误差的提取实验。
In this paper, the measurement (principle) and system of the roller method are introduced and the measurement errors are analyzed.
介绍了滚轮法测量原理和测量系统组成，分析了测量误差。
A compensation method is put forward to the error caused by temperature based on analysing the reasons of the errors in the ultrasonic measurement system.
分析导致超声波测距误差的原因，对温度引起的误差进行补偿。
The errors happening when the blast pulse signals pass the low pass filter system are obtained. It gives the basis for selecting the frequency respond range of the measurement system.
用试验的方法对爆炸脉冲信号区过低系统时带来的误差进行测定，为商量系统频响范围选取提供依据。
Finally, the effect of different errors on height measurement accuracy is simulated, and some experimental results, which can supply to system design, are presented.
最后，仿真了不同误差对测高精度的影响，实验结果符合理论分析的结果，为系统设计提供了一定依据。
The operating principle of the system is briefly narrated. The software and hardware designs of the system and the errors caused during the measurement are analyzed.
叙述该系统的工作原理，分析系统软、硬件设计及测量产生的误差。
The operating principle of the system is briefly narrated. The software and hardware designs of the system and the errors caused during the measurement are analyzed.
叙述该系统的工作原理，分析系统软、硬件设计及测量产生的误差。
应用推荐