The application of two kinds of embedded modem in MCU system is discussed in this article.
探讨了两款嵌入式调制解调器在单片机系统的应用；
This paper introduces the multi - clocks method in 8 - bit complex instruction set MCU system - level architecture.
文章介绍了一种采用多时钟定量系统设计八位复杂指令集微处理器的方法。
Emanometer is composed of normal atmosphere air mesh grid pulse ionization chamber, signal magnify and screen unit and MCU system.
仪器主要包括常压空气网栅脉冲电离室，信号放大与甄别和单片机系统。
The hardware parts of the sensor adopt the system with dual MCU and dual bus, and each dual MCU system exports the results by its respective communication bus.
该传感器的硬件采用了双单片机和双总线系统结构，每一个单片机系统都通过各自的通讯总线将处理结果输出。
Finally the program controls the output signals of the MCU system and further controls the actuation system of the robot to guide the robot to move according to the line road.
最终通过设计单片机控制程序来控制单片机系统的输出信号，从而控制机器人的驱动系统，使机器人按照引导线行进。
To raise the reliability of MCU system, this paper puts forward a design scheme based on double microcontrollers. Besides the construction, the working principle has been discussed in the paper.
本文从提高单片机系统的可靠性出发，提出了双机冗余设计方案，并就其工作原理、组成结构进行了分析。
The system achieves multi-channel temperature signal acquisition and control. Temperature limit is set by keyboard. The buzzer and relay are controlled by MCU.
本系统可以实现多路温度信号采集与显示，可以使用按键来设置温度限定值，通过进行温度数据的运算处理，发出控制信号达到控制蜂鸣器和继电器的目的。
Multipoint control unit (MCU) is the kernel of multipoint videoconference system. It offers the function of management and control for multipoint conference.
多点控制单元(MCU)是多点视频会议系统的核心，它提供多点会议的管理和控制功能。
Design of simplex wireless call and data transmIt 'system based on MCU.
基于单片机的单工无线呼叫及数据传送系统的设计。
MCU programming is carried out with assembly language, and it controls the system and collects the testing data.
单片机程序设计采用汇编语言实现，它实现了对系统的控制和数据的采集功能。
We choose MCU as the core controller in both data acquisition and the data processing system.
数据采集和处理系统均以单片机作为核心控制器。
Micro controller unit (MCU) system is the major part of the instrument, through which data collection and processing are controlled automatically.
其中单片微机系统是仪器的核心部分，通过它来实现对数据采集、处理过程的自动化控制。
With this, the paper introduces the software design of the RF reader in the system, including the general software design of MCU and every parts of the keyboard's function programs.
在此基础上，详细阐述了系统读写器的软件设计过程，介绍了读写器单片机主程序及其各键盘功能处理程序的软件开发；
The article provides a medium and small power photovoltaic control system based on MCU.
本文构建一种基于微处理器的中、小功率光伏控制系统。
The paper also describes the structure of PIC16F873 MCU, the system index, the design scheme of every module hardware and lists a detailed process.
分别描述了PIC16F873微处理器结构、系统指标及各模块硬件设计方案，并给出了详细的程序流程。
In the application system of MCU, some software anti-jamming techniques have been adopted besides some hardware anti-jamming measures.
单片机应用系统中，除采取硬件抗干扰措施外，亦常采用软件抗干扰技术。
Study on the stacker control system based on MCU.
堆垛机的单片机控制系统研究。
An ultrasonic distance measurement system controlled by the MCU of PIC16F876is described.
详细地介绍了一种由PIC 16f876单片机控制的实时超声波测距系统。
Embedded system is the hardware and software system, which has been embedded in the application of product and engineering, and is cored with MCU.
嵌入式系统是指嵌入到各种产品或工程应用中的，以微处理器或微控制器为核心的软硬件系统。
While using MCU as detecting system, input channels of measured signal should always be demanded in the system, and the necessary input information is collected by computer.
当将单片机用作测控系统时，系统总要有被测量信号的输入通道，由计算机拾取必要的输入信息。
The thesis introduces a monitor and management system on electric energy quality based on DSP, MCU, and VB. The system includes front-placed part and backstage part.
介绍了一个基于DSP、单片机及VB的电能质量监测及管理系统。该系统主要包括前端机与后台机两部分。
The kernel of embedded system is embedded MCU, which requires fast processing speed, big memory, high performance of I/O port, low power waste, and fast respond.
嵌入式系统的核心是嵌入式处理器，要求处理速度块，存储容量大，I/O口功能强，功率损耗低，及时响应快等。
This paper presents a design scheme of traffic signal lamps control system, which is based on MCU.
本文提出了一种基于单片机的交通信号灯控制系统的设计方案。
Our company is a professional development and production of 32-bit processor MCU control system, with strong technical force.
我公司是一家专业开发和生产32位处理器的单片机控制系统，拥有雄厚的技术力量。
When the valve closed for some time, and if the MCU are still working, the system can achieve re-ignition .
当气阀关闭一段时间后，如果单片机仍在工作，系统可以实现重新点火。
Methods the system utilized low power MCU MSP430F1611 and the technology as generation of bi-phase constant current stimulation.
方法：采用低功耗单片机MSP430F 1611和压控双相恒流刺激产生技术设计系统。
This paper introduces a system of MCU Read & Write Udisk based on SL811HS.
本文介绍一种基于SL811HS的单片机读写U盘的系统。
This paper introduces a system of MCU Read & Write Udisk based on SL811HS.
本文介绍一种基于SL811HS的单片机读写U盘的系统。
应用推荐