On the maximum strain criterion was proved.
实验结果与最大拉应变准则相符。
MAIN OUTCOME MEASURES: The maximum load, maximum stress, maximum strain and stress-strain curve.
主要观察指标：标本的最大载荷、最大应力、最大应变和应力-应变曲线。
Fatigue tests were performed using the 3d dumbbell specimens with different levels of maximum strain and hardness.
使用具有不同最大应变和各种硬度的3d哑铃状试样进行了疲劳试验。
Used the maximum strain-energy theory and strength limit analytic method to check the important part such as sleeve, end-plate, etc.
运用最大应变能理论和强度极限分析法，对简体、端板等重要部件进行了强度校核。
The threshold value of damage and maximum strain are adopted as failure criterion to reflect fatigue failure and ductile failure respectively.
针对材料不同的失效模式，分别采用损伤变量门槛值和最大应变作为失效判据。
By maximum tension theory and maximum strain energy density theory in fracture mechanics, created and propagation direction of new artificial fracture are analysized.
分别应用断裂力学中的最大拉应力理论和应变能密度因子理论分析了重复压裂中水力裂缝的初始扩展和延伸方向。
Results We got out the data of stretch ultimate load, maximum stress, maximum strain, elastic modulus on elbow joint ulnar nerve between control group and experimental group.
结果得出了对照组和实验组动物肘关节尺神经拉伸最大载荷，最大应力，最大应变，弹性模量等数据。
For the investigated serial propellant formulations, the maximum strain and optimum viscosity of the propellant are achieved when fine ap contents are approximately 20 percent.
对所研究的推进剂系列配方，当细ap含量接近20%时推进剂可达到最大应变与浇注中的最佳黏性。
It points out that the position of the maximum strain, stress and tension is at first group trough type roller, not at passing poion of pulley if the head drum works as pulley.
指出在头部滚筒作为驱动滚筒的布置系统中，胶带最大应变、力及张力位置不在驱动滚筒相遇点，而在过渡段第一组槽形托辊处。
A new kind of strain measuring element, the Max. Strain Memory element, is introduced in this paper. The element has the function to memorize the value of maximum strain of the loading history.
本文介绍的新型的应变测试元件——最大应变记忆元件，具有记忆构件上曾经历过的最大应变值的功能。
The fatigue test of the bellows expansion joints is replaced by the bent fatigue test of plates when the maximum strain of bent test plates equals to the local strain of bellows expansion joints.
当弯曲试板上的最大应变等于波纹管的最大局部应变时，板的弯曲疲劳试验寿命即可代替波纹管的试验寿命。
Distribution of stress, strain and milling temperature showed that stress is localized in the primary shear zone, while the maximum strain and temperature rise occurs along the tool-chip interface.
应力，应变和铣削温度分布表明，压力是定位在主剪切带，而最大应变和温度升高时沿的刀具芯片接口。
Results showed that the hardness level of drying schedules had much influence on both the drying strain developed and the time when it reached its maximum value.
结果表明，基准硬度水平对应变值的大小和最大应变值的到达时间有显著影响。
In this model, a new kinematic hardening equation was used; the non-proportionality, the effect of temperature and memorization for the maximum plastic strain amplitude were also considered.
该模型给出了一个新的背应力演化方程，引入了非比例度参量，并且还考虑了最大塑性应变幅值记忆效应和温度效应的影响。
The effects of the consolidation ratios on the maximum dynamic shear modulus and the dynamic shear modulus versus the shear strain of sands are presented by using the resonant column method.
采用共振柱试验方法，研究了固结比对砂土最大动剪切模量以及对动剪切模量比与剪应变非线性关系的影响。
Angular stiffness and elastomer shear strain on maximum swinging Angle are important indexes in flexible joint design of solid rocket motor.
角刚度(又称弹性比力矩)及弹性件在最大摆角下的剪切应变是固体发动机柔性接头设计的重要指标。
The strain criterion for ductile shear failure based on the maximum principal shear strain is established.
据此，建立基于最大主剪应变的岩土材料延性剪切破坏应变准则；
Introduced in this paper are two fracture critical surfaces of three dimensional mixed mode obtained from the theory of strain energy density factor and the theory of maximum tensile strain.
本文对按应变能密度理论和最大拉应变理论所推导出的两个三维复合型断裂临界曲面作了简要介绍。
This paper introduces a new way for defining the maximum principal strain direction in plane strain condition.
本文介绍了一种确定平面应变中最大主应变方向的新方法。
The stress for sealing washer of canned motor pump is analyzed by ANSYS software, and the maximum stress and strain of tubular sheet of press container are calculated.
主要利用ANSYS软件对屏蔽泵密封垫的应力进行分析，计算出压力容器管板的最大应力和应变。
The strain energy of the near maximum shock occurred within 15 days after the main shock.
主震后15天内最大近震的应变能量和发震时间。
It is also found that there is a close relationship between the stress in external tendon and the maximum compressive strain of the concrete flange slab.
研究还发现，体外索应力与混凝土翼板最大压应变有密切的关系。
With the increase of the grain size of H68 brass, the critical plastic strain for the onset of serrations increases while the maximum stress amplitude of serrations decreases.
对于H68黄铜，随着晶粒尺寸的增大，出现锯齿屈服的临界应变量增大，锯齿波的最大应力振幅减小。
Higher DA leads to higher value of maximum shear strain increment within the specimen. Therefore, more apparent precursor to failure can be observed at higher DA.
当扩容角较高时，应力峰值时试样内部的最大剪切应变增量较高，因而试样破坏的前兆比较明显。
When the fault displacement is same, the maximum axial compressive strain of the buried pipeline with different crossing Angle is very close.
在相同的断层位错作用下，不同穿越角度的埋地管线的最大轴向压应变十分接近。
The comparison indicates a good agreement between the experimental results and the prediction from the theory of maximum cricumferential strain criterion.
最后引用了大量试验资料验证了最大拉应变理论的适用性。
Formulated with a vigorous Cordyceps strain grown to its maximum potential.
由最好的冬虫夏草组成配方保证了最大活性。
The systolic maximum velocity and strain rate of soft plaque in carotid atherosclerosis were higher significantly than those of hard plaque(P<0.001, P<0.05).
软斑块收缩期最大运动速度、最大应变率高于硬斑块组，差异有统计学意义（P＜0.001或P＜0.05）；
Its unique strain-gauge design delivers excellent measurement precision and stability as well as providing maximum overload protection.
其独特的应变设计提供了极好的测量精度和稳定性，以及提供最大限度的过载保护。
Its unique strain-gauge design delivers excellent measurement precision and stability as well as providing maximum overload protection.
其独特的应变设计提供了极好的测量精度和稳定性，以及提供最大限度的过载保护。
应用推荐