Draw the element for maximum shear stress and mark values of all stresses.
画出最大剪应力的单元体并标出全部应力值。
The maximum shear strength of welded joints can be increased by optimizing the form of lap welding.
通过优化搭接焊形式能提高焊接接头的最大剪切力。
The straightforward procedures to achieve shear modulus of colloform and maximum shear stress are specified.
提出了求解胶体剪切模量和最大剪应力的简单方法。
The research results show that the maximum shear stress of dual-phase steel raises with the increase of martensite content.
研究表明，随着马氏体含量的增加，双相钢的最大剪切应力随之增加。
It will decrease the maximum axial stress of the lining, but it will increase the maximum shear stress and flexural stress.
开挖引致的松动区减少围岩劲度，将减少衬砌轴向应力，但增加剪应力及挠曲应力。
A combination of lateral bending plus flexion or lateral bending plus extension strongly increased the maximum shear strains.
合并有侧弯加屈曲或侧弯加伸展的运动很明显地增加了最大切应力。
Then the stress distribution of anchored rock mass with partial pull-out failure is analyzed based on the maximum shear stress criterion.
基于最大剪应力破坏准则，分析了局部脱粘破坏锚固体的应力分布。
The results show that the distributing of the maximum principal stress and maximum shear stress are mainly under the control of the landform and fault.
结果显示，隧址区的最大主压应力及最大剪应力分布主要受地形和断层的控制。
The fatigue resistance of the butt welds can be improved by means of removing the weld reinforcement and designing the weld in the maximum shear stress plane.
去除焊缝余高或将焊缝设计在最大剪应力平面内可明显改善对焊接头的疲劳性能。
Higher DA leads to higher value of maximum shear strain increment within the specimen. Therefore, more apparent precursor to failure can be observed at higher DA.
当扩容角较高时，应力峰值时试样内部的最大剪切应变增量较高，因而试样破坏的前兆比较明显。
Based on the test results and theoretical analysis, formulas to predict the initiation of cracking, yielding and the maximum shear capacity and deformation are suggested.
根据试验结果和理论分析，提出了连接键开裂、屈服和受剪承载力特征点的有关计算公式。
The calculation indicates that the maximum shear stress around inclusion is 1.2-1.7 times of that without inclusion, which has a harmful effect on the fatigue endurance of rail.
计算发现，夹杂物周围的最大剪切应力是不含夹杂物时的1.2～1.7倍，这对钢轨疲劳寿命造成有害影响。
Around the propagating fault segment the disturbed stress field of maximum shear stress displays an eight petal pattern and that of mean stress displays a four quadrant pattern.
围绕断层扩展部位剪应力增量场呈八瓣式分布，平均应力增量场呈四象限分布。
With no yielding up to its fracture strength of CFRP, the stress of CFRP at the maximum shear loading is found to be the key parameters in determining shear strength of the columns.
由于碳纤维布无屈服现象，故达到最大荷载时碳纤维布的应力是确定加固后柱受剪承载力的关键参数。
The stress accumulation in the southeastern segment of the fault since 1893 has been calculated, and the corresponding contours of maximum shear stress and hydrostatic stress are shown.
计算了1893年以来在断裂带南东段(相对闭锁段)的应力积累，示出相应的最大剪应力和流体静应力等值线图。
The results showed that most multiaxial fatigue cracks were initiated and propagated along the direction of maximum shear plane or on the direction perpendicular to the tubular specimen's axis.
研究表明，多轴疲劳裂纹主要是沿最大剪切平面或垂直于管形试样的轴线方向扩展。
Maximum shear stress generally takes place at the neutral axis of ship section.
最大剪应力通常发生在剖面的中和轴处。
Maximum shear stress generally takes place at the neutral axis of ship section.
最大剪应力通常发生在剖面的中和轴处。
应用推荐