And three-dimensional sidewall compression inlet with 25 percent cowl position has high mass capture and total pressure recovery coefficient and isolator exit flow flied is homogeneous.
整流罩位置为25%的三维侧压进气道可以获得较高质量捕获和总压恢复系数，且隔离段出口流场比较均匀。
Changes of sidewall sweep Angle and cowl position can influence inlet performance such as mass capture, total pressure recovery coefficient and uniformity of isolator exit flow field.
侧板后掠角大小和整流罩位置变化时，对进气道的质量捕获、总压恢复系数和隔离段出口流场的均匀性等都有一定的影响。
Reducing the inlet temperature of cooling water and increasing its mass flow are favorable to increase refrigerant performance coefficient, and can decrease optimal pressure at high pressure side.
降低冷却水进口温度和提高其质量流量不仅有利于提高制冷性能系数，而且能降低最佳高压侧压力。
The effects of system parameters such as system pressure, mass flow rate, heat flux and inlet sub-cooling are significant on both DWO and PWO.
系统压力、质量流速、热负荷和进口过冷度等参数对不稳定性有显著的影响。
The experimental results show that in the process of flow excursion the mass flow rate and the inlet temperature decreases, while the exit temperature increases smoothly.
研究结果表明：在发生静态流量漂移时，系统循环流量下降、加热段的进口温度下降而出口温度上升；
In the computation, the inlet of the primary flow uses the mass flowrate boundary condition. The inlet of the second flow and the outlet of the mixing flow use the pressure boundary condition.
在计算过程中，主流进口采用质量流量边界条件，二次流进口和混合流出口采用压力边界条件，均设置为环境大气压力。
The averaged Nusselt number is dramatically increased with the increase of inlet mass flow coefficient.
其它条件不变时，随流量系数的提高，平均努赛尔特数大幅度上升。
The influence of flowing area, structural of valve head, inlet density and outlet specific volume to mass flow coefficient were studied.
得到了膨胀阀的流通面积、阀头结构、膨胀阀入口密度、阀后比容对流量特性的影响，并拟合了流量系数关联式。
Some parameters, such as the inlet air humidity and temperature, the regeneration temperature, the air mass flow rate, which may affect the performance of the desiccant wheels, were also analyzed.
实验研究发现在相同工况下，氯化锂转轮的显热效率、潜热效率均高于硅胶转轮。运行参数中再生温度、处理空气进口湿度对转轮除湿性能影响比较大。
A new principle is adopted in designing low pressure MOCVD equipment. The principle is that the pressure is set and controlled separately in outlet and inlet of gas line of mass flow controller.
采用了一种新的设计原理，即以流量计为基准，将气体入口端和出口端压力双重分别统一控制，进行了低压MOCVD设计。
The dryness and mass flow rate of inlet pulp have much effect on distribution of dried plant fibers, so the suitable preceding water content ratio is 376%.
进入干燥系统的竹纤维浆料含水率和载带率对干燥后竹纤维原料的分散性影响较大。
The volumetric mass-transfer coefficient in packing increases with gas flow rate and rotating speed raises. Liquid flow rate and concentration of SO2 in inlet gas influences less on it.
转速和气体流量对旋转床填料层内的体积传质系数影响较大，流体流量和气相中二氧化硫浓度影响不大。
The volumetric mass-transfer coefficient in packing increases with gas flow rate and rotating speed raises. Liquid flow rate and concentration of SO2 in inlet gas influences less on it.
转速和气体流量对旋转床填料层内的体积传质系数影响较大，流体流量和气相中二氧化硫浓度影响不大。
应用推荐