The main compositions of supercritical CO2 fluid extraction product of Foeniculum vulgare Mill. seeds are anethole and fatty acids.
小茴香超临界CO2萃取产物的主要成分是茴香脑和脂肪酸等。
It's one of the main machines in the modern pipe mill line and formed section line.
它是现代高频直缝焊管生产线和冷弯型钢生产线的主要设备之一。
By the simulation for the transient responses of the upper shafting in the main drive system of 1150 rolling mill, the computer programme is proved to be effective.
通过对1150初轧机主传动系统上轴系机电耦合系统瞬态响应的仿真计算，证实了计算机程序的正确性。
The output and quality of metal plate and strip are heavily affected by performance of the main drive system of rolling mill.
轧机主传动系统通常由直流电机驱动，其性能好坏直接影响板带材的产量和质量。
Zirconium silicate superfine powder is an important material used in ceramic, the main process in China is wet grinding by agitating mill.
硅酸锆超细粉是建筑陶瓷的重要原料，国内主要采用以搅拌磨进行湿法研磨生产。
In this paper, the construction, work Principle, basic design and main technical characteristics of the tower Pulverizing-leaching mill were discussed.
本文论述了塔式磨浸机的构造、工作原理、基本设计过程及主要技术特点。
Therefore, it is of great importance to study the coupled dynamic characteristics of a mill main drive system for keeping efficient and reposeful production.
因此，研究轧机主传动系统的动力学耦合特性，对于抑制轧机振动、保证高效平稳地生产具有重要的理论意义和实用价值。
The axial overload is the main factor which causes work roll bearings and back up thrust bearings of four high mill invalid.
四辊轧机工作辊轴承及支承辊止推轴承失效的主要原因是轴向力过大。
The general reformation situation of main units of Cold Mill of Wuhan Iron and Steel Co. , Ltd. was introduced. The characteristics of reformation and product quality were introduced too.
介绍了武汉钢铁股份有限公司冷轧厂主要机组技术改造概况及主要技术特点；同时介绍了改造后产品的质量情况。
The main cause of this area's water pollution is the chemical substance that leaks out of a paper mill by the river bank.
这一地区水污染的主要原因是河边一家造纸厂泄漏的化学物质。
This paper introduces the present status of the cleaner production for medium or small sized wastepaper papermaking mill in China. The main problems of implementation cleaner production are analyzed.
介绍了我国中小型废纸造纸企业清洁生产的现状，分析实施清洁生产存在的主要问题，提出了促进废纸造纸行业清洁生产实施的对策。
The main products : glasscutter, glass driller, cutting machine, portable edging, diamond mill wheel, buff wheel, glass paint, shadowless glue, glass clip and advertisement nail etc.
主要产品：玻璃刀、玻璃钻头、异形切割台、手提磨边机、金刚石磨轮、抛光轮、玻璃专用漆、无影胶水、夹胶胶水、玻璃夹、广告钉等产品。
Using Reynolds equation to derivate the formula for calculating bearing pressure distribution, then calculate pressure distribution of main bearing shell of tube mill on the basis of this formula.
本文用雷诺方程推导出计算轴承压力分布的差分公式；并以此为依据，计算管磨机主轴承轴瓦的压力分布；并为轴瓦的结构设计提出建议。
Cracks and scale off are main failure forms of high Ni-Cr centrifugal combined casting roller and has great effects on mill production.
分析指出高镍铬离心复合铸造轧辊裂纹、剥落是失效的主要形式，对轧钢生产影响大。
An introduction is given to the configuration of the electric control system of a large scale radial-axial ring rolling mill and, meanwhile, its main functions and mutual relations.
介绍大型径轴向轧环机电气控制系统的结构与组成及各部分的主要功能和采用的相关技术。
The main cost of thermal power plant chiefly is the coal consumption, and the operating cost of ball mill is only the one small part . It is not necessity to do risk and sensitivity analysis.
火力发电厂的发电成本主要是煤耗，球磨机的运行费用只是发电费用中的一小部分，所以本文没有做风险分析和敏感性分析。
Modern drafting systems in the three-cylinder spinning mill are working with 10 to 200-fold main drafts.
现代纺纱厂中使用的三罗拉牵伸系统的主牵伸倍数为10 ~ 200。
This paper briefly introduces the technological flow of the straightener in Laiwu Steel Group's heavy H-beam mill and emphatically describes the main control model of the straightener.
简要介绍了莱钢大H型钢轧线矫直机的工艺流程，重点介绍了大H型钢矫直机主要的控制模型。
The components, main functions, control characteristics and gauge control method of the computer control system for single stand reversing cold rolling mill were studied.
研究了单机架可逆式冷带轧机计算机控制系统的组成、主要功能、控制特点、厚度控制方法。
The gray fabric quality is main index for the textile mill to measure technical management comprehensive level.
对于纺织厂，坯布质量是衡量企业技术管理工作综合水平的主要指标。
Through classified-testing analysis of fine wool purchased from the main material areas of Inner Mongolia, definite reference can be provided for textile mill to reasonably purchase and use wool.
通过对内蒙古自治区主要产毛区所购原毛进行分级测试分析，为纺织厂合理采购、调配使用全区的细羊毛提供了一定的参考依据。
The axial overload is the main factor which causes work roll bearings and back-up thrust bearings of four-high mill invalid.
四辊轧机工作辊轴承和支承辊止推轴承失效的主要原因是它们在工作中所受的轴向载荷过大。
Universal joint, a key part of main drive system in rolling mill, has the characteristics of complicated structure and bearing impact twisting moment when working.
万向接轴是轧机主传动系统的关键部件，具有结构复杂、工作时承受随机冲击扭矩等特点。
Warp sizing processing of textile mill is one of the main pollution sources.
纺织品制造过程中的经纱上浆工序是纺织厂重要的污染源之一。
The detecting and statistics on rolling time by using monitor protect system in the computer of main electrical machinery of rolling mill were presented in this paper.
本文提出了利用轧机主传动电动机微机在线监测保护系统对轧制时间进行检测与统计。
The current application scope of MES is introduced. The main functions, information flow and network structure of MES is discussed in light of Masteel cold mill MES.
主要介绍了当前MES系统应用范围，并就MES在马钢冷轧厂的应用具体说明该系统的一些主要功能和硬件网络架构。
The current application scope of MES is introduced. The main functions, information flow and network structure of MES is discussed in light of Masteel cold mill MES.
主要介绍了当前MES系统应用范围，并就MES在马钢冷轧厂的应用具体说明该系统的一些主要功能和硬件网络架构。
应用推荐