The effect of the wiring ways on voltage quality is analyzed according to the relations between load moment and voltage loss.
文章根据负荷矩与电压损失的关系分析了接线方式对电压质量的影响。
In general, to the components in the cable-stayed bridge, the load moment of key position caused by the wind load on the cable take a large proportion of total.
一般来讲，在斜拉桥诸多构件当中，由斜拉索风荷载引起的桥梁特殊位置弯矩响应占着不小的比重。
For the safe operation of jib cranes, load moment limiters need to be installed to monitor and control values of load and radius influencing the value of load moment.
为了保证臂架式起重机的安全工作，必须安装能监测载重、幅度等影响起重机力矩因素的力矩保护器。
By making compromise between the least line load moment and the largest load demand satisfaction degree, the right-of-way selection under uncertain load forecasting is well resolved.
通过在线路负荷矩最小与各用户负荷需求满足程度最大之间求最佳折衷平衡，解决了负荷预测不确定情况下的路径优化问题。
Load moment limiter is a safety device with comprehensive function. The accuracy and reliability in work of the device are certainly restricted by factors both mechanical and electrical.
力矩限制器是具有机械与电气技术综合功能的安全装置，其工作精度和可靠性必然受到这两方面因素的制约。
In view of the uncertainty in the load moment of inertia and the disturbance of test table with three or more axes, a discrete time model reference adaptive control is presented in this paper.
针对多轴转台中负载转动惯量和干扰力矩的不确定性，提出了一种离散的模型参考自适应控制方法。
With Web sites, we talk about load in terms of concurrent users, which does not necessarily mean that every user is requesting a page at the exact same moment, which is a common misconception.
对于网站，我们常常从并发用户的角度来讨论负载问题，这并不一定意味着每个用户都在完全相同的时刻请求某个网页，这其实是一种常见的误解。
This makes the bolt bear the preload and work load, but also bear the role of additional bending moment.
这使螺栓在承受预紧力和工作载荷作用的同时，还要承受附加弯矩的作用。
This simultaneous generATion and transmission with use requires power system capacity to meet the load demand AT whATever moment it occurs.
这种随时按用电需求来发电和输电就要求电力系统的容量在无论什么时刻都能满足负荷的需求。
This method can be used to analyze accurately the complete load-deformation response of RC beams loaded in combined shear, moment, and axial load.
该法可以对在弯矩、剪力和轴力共同作用下的钢筋混凝土梁截面进行较为准确的荷载-变形反应全过程分析。
Distributed load is regarded as polynomial function or uniformly distributed moment all ng the edge.
荷载采用了多项式形的分布荷载及均布边缘力矩。
The distributed load is regarded as polynomial function or uniformly distributed moment along the edge.
荷载采用了多项式型的分布荷载及均布边缘力矩。
Total coefficient of modulation of moment for the frame applied horizontal load and vertical load is bigger than that of the same frame applied vertical load.
框架既承受水平荷载又承受竖向荷载时的总弯矩调幅系数比相同结构只承受竖向荷载的总弯矩调幅系数大。
Slewing ring bearings to withstand a large-scale integrated load bearing support, which can bear a greater axial load, radial load and tipping moment.
回转支承轴承是一种能够承受综合负荷的大型支承轴承，可同时承受较大的轴向负荷、径向负荷和倾翻力矩。
The simulation experiment shows that the system has better performance of vibration suppression control and stronger robustness for modeling error of load inertia moment.
仿真实验表明，该系统具有良好的防振控制性能，而且对负载惯性矩的模型化误差具有较强的鲁棒性。
The methods of load balance of moment limiting and speed softening mode under torque control model and velocity mode are put forward.
提出了在转矩模式、速度模式下力矩限幅和速度软化方式的负荷平衡方法。
Internal force of curve beam under uniform load is analyzed in this paper, and simplified method of computing moment is given.
本文分析并推求了均布荷载下平面弧形梁的弯矩、扭矩计算公式，并提出弯矩的简化计算方法。
By comparing the ways of plastic analysis, the plastic moment coefficient and load coefficient are used to illustrate the collapsing load formula of mobile-structure.
本文通过对塑性分析方法比较，采用了塑性弯矩系数和荷载系数来表达机构破坏荷载公式。
The thesis describes the methods to improve the system accuracy against instant torque moment by reducing the additional torque caused by the load impact and increasing the system stiffness.
文章主要论述在随动系统的设计研制实践中，如何通过减小负载冲击力作用时所产生的附加冲击力矩和采取增加系统本身抗冲击力矩刚度等方法。
For two Three-Columniation End moment Equations at neighbor points, moved out sidesway, it is Three-span moment Equation of frame that be relationship moments in three spans with load.
利用在连续两个结点上的三柱端弯矩方程，消去侧移分量产生刚架连续三跨的柱端弯矩与荷载关系的三跨弯矩方程。
On the basis of mechanical model and formula of single bit, the moment model and load fluctuation model of shearer's drum are built.
根据单个截齿的受力模型和计算公式，建立了采煤机滚筒力矩模型和载荷波动模型。
The influence of the vertical load to the horizontal capacity is evaluated via calculating the overturning force moment borne by the vertical counterforce.
叙述了一种新的承载力简化计算方法，这种方法通过垂直土反力承担抗倾覆弯矩，来考虑垂直荷载对水平承载力的影响。
Results Obtained the distortion deformation, stress nephogram, section stress of femur neck and upside of femoral shaft of the femur under the bending moment and compressive load.
结果得出了在弯压复合荷载下股骨的变形、应力云图、股骨颈和股骨干上端的截面应力。
The limit load formulae of single-edge deeply notched plates with round ends subjected to pure bend moment and tensile load under plane stress condition have been derived.
推导了平面应力条件下单边圆形底部深缺口板条受纯弯曲和拉伸载荷作用的极限载荷公式。
The result shows that load simulation system has a nice tracking characteristic by means of nonlinear control law, and the redundant moment brought by strong disturbance can be effectively restrained.
结果表明，采用非线性控制规律，负载模拟系统的跟踪特性好，且系统能有效抑制强扰动所引起的多余力矩。
In order to analyze the load deformation, a single spring dual moment inertia model was used to model the load of dual hydraulic motor synchronizing driving (DHMSD) system.
针对双液压马达同步驱动系统建模过程中存在负载变形考虑不足的情况，采用单弹簧、双惯量块代替单惯量模型建立负载动力学模型；
The optimization design method can also be used in the balance of non-sinusoidal changing load resistance moment and has important value of application popularized.
对非正弦变化的负载阻力矩的平衡也可应用本设计的优化方法，有推广价值。
Based on mechanics analysis of elevating system with balancing weight, the additional driving moment that the motor have to supply for accelerating a inertia load is obtained.
首先对有对重的提升系统进行了力学分析，得出了加速阶段由于惯性的作用电动机必须提供的附加力矩。
Considering radial load, axial load, centrifugal force and gyroscopic moment acted on the ball bearing simultaneously, an analysis model based on quasi-dynamic method was set up in this paper.
本文利用拟动力学法，同时考虑径向负荷、轴向负荷、自身离心力以及陀螺力矩作用的影响，建立了高速滚珠轴承载荷分布的分析模型。
Considering radial load, axial load, centrifugal force and gyroscopic moment acted on the ball bearing simultaneously, an analysis model based on quasi-dynamic method was set up in this paper.
本文利用拟动力学法，同时考虑径向负荷、轴向负荷、自身离心力以及陀螺力矩作用的影响，建立了高速滚珠轴承载荷分布的分析模型。
应用推荐