The polarization of electrode decreased and the heavy load discharge performance of battery were improved by using foamed nickel.
使用发泡镍可降低电极的极化，改善电池的大电流放电性能。
The charge-discharge performance of the electrode was improved by surface treatment, especially heavy load discharge performance.
表面处理改善了电极的充放电性能，特别是大电流放电性能。
Parameter test and load discharge can process at one time. It is controlled by CPU, and can automatically test three-phase voltage, current and power ETC.
参数检测和带载放电同时进行，单片机控制，可自动检测三相电压、电流、频率等参数。
Measurements of stray field within the plasma region and magnetizing curve of the iron core were made in a model device with variation of air gap size and under load and unload discharge conditions.
模拟实验给出了不同气隙情况下，空载和负载放电时，等离子体区的杂散场和铁芯磁化曲线测试结果。
Germany sunshine battery deep discharge resistance is strong, 100% still can pick up on the load continuously after discharge, dominant charging can restore the revival capacity of 95% in January.
德国阳光蓄电池抗深放电能力强，100%放电后仍可连续接在负载上，在一月支配充电可恢回复复兴容量95%。
This circuit will disconnect the load if the battery gets close to deep discharge, and reconnect it only when recharge is well underway.
如果电池深放电接近该电路将断开负载，并重新连接，只有当补给正在有条不紊地进行。
The testing principle and the performing method of testing items such as speed, range, load, discharge voltage and current for electro-hybrid bicycle are described based on deciding the items.
分析和确定了电动助力车主要性能的检测项目，并对车速、续行里程、载荷、蓄电池的放电电压和放电电流等被测项目的检测原理及实现方法进行了探讨。
The system perfects the management and protection for the charge and discharge of storage battery also for the load and solar power supply.
从硬件、软件方面完善系统对蓄电池充放电及其负载的管理和保护。
The matching question of the load and the choice question of the discharge time are discussed in detail.
对负载的匹配问题和放电时间的选择问题作了较详细的讨论。
In the invention, discharge of falling off capacitance supplies power dissipation of short time load for complete device.
当整机电源输入口电压跌落时，本发明电路的抗跌落电容放电，能为整机提供短时负载功耗。
Shock wave and thermal load are the two main effects on the envelope during the discharge.
放电过程中，灯管主要受冲击波和热负载两方面的作用。
The maximum diurnal average load is consistent with the peak of discharge, indicating that water and soil losses occur largely during the rain storms.
最大日平均输沙率均与最大流量峰值对应，说明水土流失主要发生在暴雨期间。
An appropriate formula of bed load rate is chosen to calculate the amount of bed load of each section. Curves of amount of bed load and discharge are got.
比较选用能较适用于该河段的推移质输沙率公式，计算出各断面的推移质输沙量，得出推移质输沙量与流量的关系曲线。
It has discharge models of constant-current. After setting parameter, it can achieve capacity test to battery and load capacity test to DC power.
恒流放电模式，参数设定后自动完成蓄电池组的容量测试或直流电源的带载能力检测。
It can extend the life of battery and decrease ups system failure rate to the problem of under-voltage, low capacity and discharge current not meeting load startup request.
主要针对UPS蓄电池段电压不够、容量不足或瞬间放电电流不满足带载启动要求等问题。可以延长蓄电池的使用寿命，降低UPS系统故障率。
The introduction of a new type preciptant for treatment of hydrolysis product lower the production cost and load of waste discharge.
引入了一种新型的沉析剂处理水解产物，降低了生产成本和排污负荷。
The relationship between the discharge levy amount and the total pollution load retains a highly positive correlation.
废水排污收费总额与污染负荷高度线形相关；
As a result, China began to introduce "total load" limits into its regulatory model to cap the total discharge of certain "major" pollutants.
因此，中国开始在其治理模式中引入“排放总量”限制，以便对特定的“主要”污染物的总排放量设置上限。
Subject to the provisions of Article IV, the carrier shall properly and carefully load, handle, stow, carry, keep, care for and discharge the goods carried.
除第四条条文另有规定外，承运人应当妥善地、谨慎地装载、处理、积载、运输、保管、照料及卸载所运货物。
The carrier shall properly and carefully load, handle, stow, carry, keep, care for and discharge the goods carried.
第四十八条承运人应当妥善地、谨慎地装载、搬移、积载、运输、保管、照料和卸载所运货物。
Pump discharge of oil with reasonable design, gear oil and back at work under minimum torque force bearing load, so small, wear small, pump with high efficiency.
泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
Pump discharge of oil with reasonable design, gear oil and back at work under minimum torque force bearing load, so small, wear small, pump with high efficiency.
泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
应用推荐